Closed shahram241 closed 1 year ago
ok. and vin also ok )). My Congratulations ))
Please remove the logs from the thread.
Done?
Yes. You have repaired your r-link!
I asked to remove logs only because they contains your vin
Thank you very much. Thank you very much. Thank you very much.
Ok)
Could it be a good idea to add this script as a plugin ?
It contains a lot of parameters special only for this car. The set of options. Screen parameters, acoustic parameters of talisman car body and so on. I afraid it do not suite to other cars with r-link2. Kadjar, Megane4 Koleos and so on. We may do a plugin for screen repair. It would contains only two option for MID and HIGH screens. It should be enough for turning on the screen.
A lot of other parameters may be repaired by ddt4all
Ok, what are the main parameters to set to get it back to life ?
It is for MID
2E230301F404080801E03C0000039D000A0005006E03200AD7022C006967
and for HIGH
2E2303032802131303003C000004500014001E001E040011C5002C006967
Thanks, I'll try to add that as a plugin. Which vehicles are concerned with those frames ?
Congratulation for this script! I've a request and I hope that you can help me. I Have a Megane 4 with 8,7" display and it's fully working but I also have a second hands Rlink2 unit taken from a car with 7" screen (I saw on the top the software version 3.3.16.941 so for small screen). If I connect this unit to my car is not available because I think is due to the old VIN code written on it....there is a way to erase that code and after turn it on with my 8,7" screen? Or not? Thanks a lot
...and, if you need all the parameters for a Megane 4 Bose 1.6 dci, I'm here!
@cedricp these parameters are suited for all R-Link2. As I know R-Link2 is installing on Kadjar, New Koleos, Megane4, Scenic4, New Clio, Talisman and new Espace
@igno77 I may do similar script for your car while my lab is prepared for it. Just give me your e-mail. But... Did you try this? https://www.gps-rlink.com/2018/11/15/r-link-2-the-3-3-16-960-update-is-avalaible-for-download/
Then do you know that the main problem is to extract old box before installing the new one? You have to disassemble almost all dashboard for get the r-link2 from inside http://www.club-renault.ru/forum/topic/75668-%D0%BC%D1%83%D0%BB%D1%8C%D1%82%D0%B8%D0%BC%D0%B5%D0%B4%D0%B8%D0%B9%D0%BD%D0%B0%D1%8F-%D1%81%D0%B8%D1%81%D1%82%D0%B5%D0%BC%D0%B0-r-link-2/?page=30&tab=comments#comment-2172117 If you are going to do it for a first time then it would take 4-5 hours only for disassemble.
@shrlnm yes, I've installed the 3.3.16.966 without any problem but what I would like to know is a way to unlock an rlink board that are not visible in my can bus because has a different VIN code written on it. This is not the first time that I dismount the Rlink system so I know....a long and hard work !!
@igno77 Ok. From problem description I understand that you have r-link box with 3.3.16 installed on your car. The r-link is functional except availability thru CAN bus. Am I right? Does it send any response (negative or positive) or it do not response at all? Could you please send me log with try to connect to it?
@cedricp I forgot to note that after changing any configuration of r-link2 we have to reboot it by command 1101
@shrlnm In my car I have a native 3.3 unit full working on my 8,7" but I have second hand 3.3 unit on my desk with installed version 3.3.16.941 (so for 7" display). Yesterday I had putted inside my car the second hand unit and I can see it with obd/ddt4all!!!!!! I've reconfigured every pages of radnav with right values but the only one that I can't change is the VIN code. BTW the screed still black and no music...totally dead! I think that I need a special script like the activation made in Renault service when you change the rlink unit with a new one. And, after that, how can I activate the multimedia services on that unit? This is very important due to connect the vin code to the rlink code and unlock the download from my renault website.... What's your feeling?
@igno77 first we need to be sure that the wiring is the same on both units and video output is not broken on the second hand unit. As I know, there is no screen blocking function in r-link2 so let's check that you defined screen parameters well for your 8,7" screen. Did you do any screenshots or may be you got dumps from the unit? I suppose that the screen should works if the android starts.
We may write new vin only when the unit have no vin inside. You may clear current vin by virgin mode (but you need working screen for that (( )
We may also try to remove current vin by the CAN command 1140 but I not sure that it clears the vin.
Anyway I may do config for you similar as for @shahram241, give me your e-mail or vin here or thru another channel I suppose you know ;)
@shrlnm I'm not sure that this unit was working...it's sencond hand. I'm sure about the screen parameters becasue were copied from my working system but the screen was still black, I this we need such a kind of "special restart" for wake it up. Unfortunately I don't have any screenshot :-( Are you sure that we need the screen for virgin mode? I never tested before, only in demo mode, so I don't know also if we can reach this ecu or not, but on (ALL cars), S-GW3, C1A_CGW_DDT_6.1.1 there is a section for exit from Virgin mode! My mail is igno_v@hotmail.com Thanks
@shrlnm I pressed virgin mode R-Link screen gone.Screen was opened by the service.But
VIN was removed from R-Link 2. Car don't write .wls files when I connect the usb to the car . I have Elm37 wifi. My car is Megane 4. Help me please. My e mail : willyvalve@hotmail.com
Hello @WillyVALVE As so the garage repaired main parameters with the CLIP, you may just write the VIN by ddt4all. Did you try it?
@shrlnm ddt4all gives error when I click on the Identification but its works other configuration commands
@WillyVALVE Could you please send log files and content of second window (behind the main one on picture) it contains some error messages
@shrlnm
There are no tries to write the VIN in the logs. The error messages fires because you have symbols 0xFF instead of vin number and they can not be converted to ascii and after that as I see the ddt screen shows nothing. Am I right?
I sent you an e-mail.
@shrlnm VIN is OK. Thanks for all.
Sana vin ile 10 dakika içinde yeni senaryo göndereceğim
merhaba bu kullandığınız programın adı nedir.
@shrlnm ddt4all dışında kullandığınız diğer programın adı nedir? paylaşmanız mümkün mü?
@suleymanpanko https://gitlab.com/py_ren/pyren
Hello all, same from my side I accidentally clicked on virginmode :( and my screen is black now. I tried to follow the steps shared here : https://gitlab.com/py_ren/pyren/wikis/how%20to%20rlink2%20black%20screen by shrlnm however I dont know how to verify if the script is running.
The launcher asks to define the connection , i selected bluetooth then searched for the macro. But how to verify if it was successful or not?
My car is a megane 4 and i have an ELM327 bluetooth device with a windows 10 laptop.
Thank you all for your help
The launcher asks to define the connection , i selected bluetooth then searched for the macro. But how to verify if it was successful or not?
You may verify it by log files from pyren/logs folder.
Im newbie i have no idea what all this mean :) . Based on your thread i only understood that for my car i should use MID macros because my screen is the 7 inches one.
But the macros seems to stuck in the 4 first code lines nothing happens, how much time do I need to wait please ?
But the macros seems to stuck in the 4 first code lines
Yes, your ELM is bad Chinese clone
[16:28:09.254]AT CRA 732 <[0.004]AT CRA 732 OK
[16:28:09.267]AT FC SH 712 <[0.016]AT FC SH 712 ?
Looks like there's only those clones remaining on the market :(
All clear now so I could do nothing with this device. Thanks anyway for your help and also for the clear tutorial you created. Its the only one existing over the internet I think. Amazing job
Sometimes it is possible to buy suitable. The main rule is to ask the adapter based on PIC processor.
Ifinally went to renault dealership who done a reset using Renault Clip. However the screen remains blank; only radio sound works. In other terms ive lost the rear camera and the other multimedia functions.
Bonsoir jai le meme probleme sur ma talisman. Ecran noir mais jai réussi a le récupérer. Mai mantenant jai l ecran a la vertical. Je suis em mode eco plus de mode de conduite, plus de son, plus de reglage ventilation.plus de massage Quelqun a une solution merci
possible to remove this protection through devmode with antitheft Help renault espace 5 rlink 2
Hello there. How to change rlink2 VIN number with ddt4all. I would be glad if you help
Hello I will ask for help in starting R-link2 after pressing virginmode. My car is Megane 4 2018. The radio has 7 "I have an ELM327 interface on USB.
I will ask for help in starting R-link2 after pressing virginmode.
give your e-mail please.
klaja@wp.pl
And i hawe anorlther problem. Can i vyrginize a used radio with , to use iylt in my vehicle? Problem is my radio was in water and not working anymore. I hawe used radio, but there is anti theft is activated. On the screen is: Anti theft activation , system locked. Only new radio needed ??? Or i cam do anything
r-link 2 system block how to unlock? how to change the v.i.n code of the car radio
I am french iam not speak english sorry
You cannot change vin. Only new vin in new or virgyn
hello I selected the virgin mode (developer mode). Please help to exit this virgin mode. Thanks