issues
search
eez-open
/
psu-firmware
Firmware for programmable bench power supply EEZ H24005
https://www.envox.eu/bench-power-supply/psu-firmware/
GNU General Public License v3.0
167
stars
60
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
sd_card.cpp:63:60: error: no matching function for call to 'SdFs::cardBegin(const uint8_t&, long unsigned int)'
#218
majzel
closed
3 years ago
0
Cannot compile firmware for older boards
#217
dsaltas
closed
4 years ago
4
Compilation issues with Visual Micro
#216
jfitter
closed
4 years ago
1
Multimeter
#214
thesourcerer8
closed
5 years ago
1
Initial task list for adding support for STM32F7 MCU board
#211
prasimix
closed
5 years ago
1
Rotary encoder issue
#210
AndersWestman
closed
6 years ago
2
Calibration seems very off after upgrading
#208
Cabalist
closed
5 years ago
1
Manual&Step Trigger is not working
#207
sujitth
closed
5 years ago
1
Increase SPI speed for W5500
#206
prasimix
closed
6 years ago
1
Reduce SD card SPI clock speed
#205
prasimix
closed
6 years ago
1
Not possible to configure Ethernet without DHCP
#204
mvladic
opened
6 years ago
0
Trigger cannot start if output values are limited on other channel
#203
prasimix
closed
6 years ago
1
Support for the Power board r5B13
#202
prasimix
opened
6 years ago
0
SCPI limit fix for for voltage/current/power
#201
ZakDanger
closed
6 years ago
0
Using SCPI over usb serial then over ethernet causes a problem
#200
ZakDanger
closed
6 years ago
26
Readme updates to include board and port selection
#199
ZakDanger
closed
6 years ago
0
Internal data logging (SCPI only)
#198
prasimix
closed
6 years ago
3
Fan fail message during startup self-test when using a larger, slower fan.
#197
morris6
closed
6 years ago
2
Outputs protection when out of range voltage is measured
#196
prasimix
opened
6 years ago
0
Initate touchscreen calibration when calibration data are lost or corrupted
#195
prasimix
closed
6 years ago
3
Switch off all outputs when reverse polarity tripped
#194
prasimix
closed
6 years ago
1
Can't enable serial with non 9600 baud rate
#193
Helix70
closed
6 years ago
1
Change subsystem for DIGital SCPI commands
#192
prasimix
closed
6 years ago
1
False attempt to calibrate current without load connected
#190
romain145
closed
6 years ago
6
Unable to compile sketch in Arduino: 'pages' not declared
#189
richiewebgate
closed
6 years ago
2
Fan speed control logic
#188
kolesar007
closed
6 years ago
9
Erratic premature disabling of down-programmer on output off with INHibit
#187
prasimix
closed
6 years ago
1
Increasing value by encoder in confirmation mode
#186
prasimix
closed
6 years ago
3
Consolidate error messages for calibration and system password
#185
prasimix
closed
6 years ago
1
Decrease frequency of saving changes into EEPROM
#184
prasimix
closed
6 years ago
2
Power limit warning can be overridden in serial coupling mode
#183
AndersWestman
closed
6 years ago
3
DEBUg? blocks MCU when send via serial
#182
prasimix
closed
6 years ago
1
Daylight saving (DST) change failed
#180
prasimix
closed
6 years ago
8
Channel with active trigger affect other channel
#179
prasimix
closed
6 years ago
1
SYSTem:COMMunicate:RLSTate? is not implemented
#178
prasimix
closed
6 years ago
1
SYSTem:DIGital:OUTPut:DATA? is not implemented
#177
prasimix
closed
6 years ago
1
Step mode value storage
#176
AndersWestman
closed
6 years ago
3
Change identification string
#175
prasimix
closed
6 years ago
1
Restarting list when trigger is still active
#174
prasimix
closed
6 years ago
1
User profile recall can affect output state when protection trip is not cleared
#173
prasimix
closed
6 years ago
1
SYSTem:COMMunicate:ENABle does not affect displayed icon
#172
prasimix
closed
6 years ago
2
Won't allow me to save calibration
#171
reportingsjr
closed
6 years ago
18
YT-view display issue
#170
prasimix
closed
6 years ago
1
Various issues with channel triggering
#169
prasimix
opened
6 years ago
0
Test
#168
mvladic
closed
6 years ago
0
Invalid protection trip condition when enters coupling mode
#167
prasimix
closed
6 years ago
4
Pin1 inhibit functionality
#166
prasimix
closed
6 years ago
1
Prepare .HEX/.bin for direct firmware upload without Arduino IDE
#165
prasimix
closed
6 years ago
7
Unable to upload 1.01 firmware 'SerialUSB was not declared in this scope'
#164
jcg747
closed
6 years ago
10
Both channel output is active during firmware updating. No indication that channels are active
#163
DwaineGarden
closed
5 years ago
2
Next