fietser28 EL-Load issues

fietser28 / EL-Load

6 stars 0 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Add EEPROM delete command

#49 fietser28 opened 20 minutes ago
0
Implement reverse polarity FW support

#48 fietser28 opened 25 minutes ago
0
Add event log

#47 fietser28 opened 1 hour ago
0
Refactor calSetDefaults

#46 fietser28 opened 1 hour ago
0
ADD Beeper config screen and settings

#45 fietser28 closed 2 weeks ago
1
Standalone enclosure design

#44 fietser28 closed 1 week ago
1
Add basic statistic support

#43 fietser28 closed 1 week ago
1
Add RP2350 support

#42 fietser28 closed 3 weeks ago
0
Implement MEASure commands

#41 fietser28 opened 6 months ago
0
Check/test rise fall time compatibility of inputs to logic

#40 fietser28 opened 6 months ago
0
Demo dashboard: MPPT for small solar panels

#39 fietser28 opened 7 months ago
0
Implement self test and *TST?

#38 fietser28 opened 7 months ago
0
Define and agree on SPI messages

#37 fietser28 opened 7 months ago
0
Document & clean/refactor firmware architecture

#36 fietser28 opened 7 months ago
0
Add/finish SHORT mode

#35 fietser28 opened 7 months ago
0
Document SCPI commands

#34 fietser28 opened 7 months ago
0
Add BB3 firmware support to BB3 FW

#33 fietser28 opened 7 months ago
0
Firmware split between module and control

#32 fietser28 opened 7 months ago
1
Add programmable slew rate circuitry

#31 fietser28 opened 7 months ago
0
BB3 compatible MCU board

#30 fietser28 opened 7 months ago
0
Standalone PCB with DIB connector.

#29 fietser28 opened 7 months ago
0
Analog V4 testing

#28 fietser28 opened 7 months ago
0
Add mounting holes for heatsink on PCB

#27 fietser28 closed 7 months ago
0
Add heatsink mounting holes to PCB

#26 JanNieuwstad closed 7 months ago
0
Add LED mode

#25 fietser28 opened 7 months ago
0
Select isolation transformer T1/T2

#24 fietser28 opened 7 months ago
0
Swap Von and VonLatch in firmware for v4 MCU PCB

#23 fietser28 closed 1 week ago
1
MCP23017 GPA7 is output only according to datasheet

#22 fietser28 closed 7 months ago
1
range switching doesn't always work

#21 fietser28 closed 8 months ago
2
Evaluate low voltage range

#20 fietser28 closed 8 months ago
1
Evaluate low current range

#19 fietser28 closed 8 months ago
1
Remove ADC clamp circuits

#18 fietser28 closed 7 months ago
0
Implement watchdog

#17 fietser28 closed 5 months ago
1
Von scaling

#16 fietser28 opened 8 months ago
0
PCB changes for DIB/BB3 compatibility

#15 fietser28 opened 8 months ago
1
Add nice reverse polarity protection and detection.

#14 fietser28 opened 8 months ago
2
Von circuitry might oscillate with specific loads

#13 fietser28 opened 8 months ago
0
Add testpoints

#12 fietser28 closed 7 months ago
0
Test with powerful fan

#11 fietser28 closed 6 months ago
1
12V to 5V convertor

#10 fietser28 closed 7 months ago
0
Change clamping circuit

#9 fietser28 opened 8 months ago
2
CC loop tuning

#8 fietser28 closed 7 months ago
1
Make Power section dual voltage input

#7 fietser28 closed 7 months ago
0
Add ESD protection

#6 fietser28 closed 7 months ago
2
Add USB-C connector with USB-C PD sink capability

#5 fietser28 opened 8 months ago
0
Fix errors on EL-Load-Analog v3-C Schema & PCB

#4 fietser28 opened 8 months ago
0
Fix Errors on EL-Load-Panel PCB 1r1

#3 fietser28 closed 9 months ago
0
Fix errors on EL-Load-Power-MCU 2r2

#2 fietser28 closed 7 months ago
0
Optimise MOSFET placement on heat sink and/or power distribution between MOSFETS.

#1 fietser28 opened 9 months ago
7