A collection of functions for assisting in converting extracted raw data from infrared thermal images and converting them to estimated temperatures using standard equations in thermography. Provides an open source proxy tool for assisting with infrared thermographic analysis.
The version here on github is the current, development version. Archived sources can be found: https://cran.r-project.org/src/contrib/Archive/Thermimage/
2021-09-23: Version 4.1.3 is on Github (development version)
Glenn J. Tattersall. (2017, December 3). Thermimage: Thermal Image
Analysis.doi: 10.5281/zenodo.1069704 (URL:
http://doi.org/10.5281/zenodo.1069704), R package, <URL:
https://CRAN.R-project.org/package=Thermimage>.
# install.packages("Thermimage", repos='http://cran.us.r-project.org')
# library("devtools"); install_github("gtatters/Thermimage",dependencies=TRUE)
Imports: tiff, png
Suggests: ggplot2, fields, reshape
Normally, these thermal images require access to software that only runs on Windows operating system. This package will allow you to import certain FLIR jpgs and videos and process the images in R, and thus is platform independent.
To load a FLIR JPG, you first must install Exiftool as per instructions above. Open sample flir jpg included with Thermimage package:
library(Thermimage)
f<-paste0(system.file("extdata/IR_2412.jpg", package="Thermimage"))
img<-readflirJPG(f, exiftoolpath="installed")
dim(img)
## [1] 480 640
The readflirJPG function has used Exiftool to figure out the resolution and properties of the image file. Above you can see the dimensions are listed as 480 x 640. Before plotting or doing any temperature assessments, let’s extract the meta-tages from the thermal image file.
cams<-flirsettings(f, exiftoolpath="installed", camvals="")
head(cbind(cams$Info), 20) # Large amount of Info, show just the first 20 tages for readme
## [,1]
## ExifToolVersionNumber 12.26
## FileName 2412
## Directory ".4.0"
## FileSize 638
## FilePermissions "--"
## FileType ""
## FileTypeExtension ""
## MIMEType ""
## JFIFVersion 1.01
## ExifByteOrder "-"
## Make ""
## CameraModelName 660
## Orientation ""
## XResolution 72
## YResolution 72
## ResolutionUnit ""
## Software "1.1.98"
## YCbCrPositioning ""
## ExposureTime 133
## ExifVersion 220
This produes a rather long list of meta-tags. If you only want to see your camera calibration constants, type:
plancks<-flirsettings(f, exiftoolpath="installed", camvals="-*Planck*")
unlist(plancks$Info)
## PlanckR1 PlanckB PlanckF PlanckO PlanckR2
## 2.110677e+04 1.501000e+03 1.000000e+00 -7.340000e+03 1.254526e-02
If you want to check the file data information, type:
cbind(unlist(cams$Dates))
## [,1]
## FileModificationDateTime "2021-09-23 18:46:07"
## FileAccessDateTime "2021-09-23 19:08:42"
## FileInodeChangeDateTime "2021-09-23 18:46:09"
## ModifyDate "2013-05-09 16:22:23"
## CreateDate "2013-05-09 16:22:23"
## DateTimeOriginal "2013-05-09 22:22:23"
or just:
cams$Dates$DateTimeOriginal
## [1] "2013-05-09 22:22:23"
The most relevant variables to extract for calculation of temperature values from raw A/D sensor data are listed here. These can all be extracted from the cams output as above. I have simplified the output below, since dealing with lists can be awkward.
ObjectEmissivity<- cams$Info$Emissivity # Image Saved Emissivity - should be ~0.95 or 0.96
dateOriginal<-cams$Dates$DateTimeOriginal # Original date/time extracted from file
dateModif<- cams$Dates$FileModificationDateTime # Modification date/time extracted from file
PlanckR1<- cams$Info$PlanckR1 # Planck R1 constant for camera
PlanckB<- cams$Info$PlanckB # Planck B constant for camera
PlanckF<- cams$Info$PlanckF # Planck F constant for camera
PlanckO<- cams$Info$PlanckO # Planck O constant for camera
PlanckR2<- cams$Info$PlanckR2 # Planck R2 constant for camera
ATA1<- cams$Info$AtmosphericTransAlpha1 # Atmospheric Transmittance Alpha 1
ATA2<- cams$Info$AtmosphericTransAlpha2 # Atmospheric Transmittance Alpha 2
ATB1<- cams$Info$AtmosphericTransBeta1 # Atmospheric Transmittance Beta 1
ATB2<- cams$Info$AtmosphericTransBeta2 # Atmospheric Transmittance Beta 2
ATX<- cams$Info$AtmosphericTransX # Atmospheric Transmittance X
OD<- cams$Info$ObjectDistance # object distance in metres
FD<- cams$Info$FocusDistance # focus distance in metres
ReflT<- cams$Info$ReflectedApparentTemperature # Reflected apparent temperature
AtmosT<- cams$Info$AtmosphericTemperature # Atmospheric temperature
IRWinT<- cams$Info$IRWindowTemperature # IR Window Temperature
IRWinTran<- cams$Info$IRWindowTransmission # IR Window transparency
RH<- cams$Info$RelativeHumidity # Relative Humidity
h<- cams$Info$RawThermalImageHeight # sensor height (i.e. image height)
w<- cams$Info$RawThermalImageWidth # sensor width (i.e. image width)
Now you have the img loaded, look at the values:
str(img)
## int [1:480, 1:640] 18090 18074 18064 18061 18081 18057 18092 18079 18071 18071 ...
If stored with a TIFF header, the data load in as a pre-allocated matrix of the same dimensions of the thermal image, but the values are integers values, in this case \~18000. The data are stored as in binary/raw format at 2^16 bits of resolution = 65536 possible values, starting at
temperature<-raw2temp(img, ObjectEmissivity, OD, ReflT, AtmosT, IRWinT, IRWinTran, RH,
PlanckR1, PlanckB, PlanckF, PlanckO, PlanckR2,
ATA1, ATA2, ATB1, ATB2, ATX)
str(temperature)
## num [1:480, 1:640] 23.7 23.6 23.6 23.6 23.7 ...
The raw binary values are now expressed as temperature in degrees Celsius (apologies to Lord Kelvin). Let’s plot the temperature data:
library(fields) # should be imported when installing Thermimage
plotTherm(temperature, h=h, w=w, minrangeset=21, maxrangeset=32)
The FLIR jpg imports as a matrix, but default plotting parameters leads to it being rotated 270 degrees (counter clockwise) from normal perspective, so you should either rotate the matrix data before plotting, or include the rotate270.matrix transformation in the call to the plotTherm function:
plotTherm(temperature, w=w, h=h, minrangeset = 21, maxrangeset = 32, trans="rotate270.matrix")
If you prefer a different palette:
plotTherm(temperature, w=w, h=h, minrangeset = 21, maxrangeset = 32, trans="rotate270.matrix",
thermal.palette=rainbowpal)
plotTherm(temperature, w=w, h=h, minrangeset = 21, maxrangeset = 32, trans="rotate270.matrix",
thermal.palette=glowbowpal)
plotTherm(temperature, w=w, h=h, minrangeset = 21, maxrangeset = 32, trans="rotate270.matrix",
thermal.palette=midgreypal)
plotTherm(temperature, w=w, h=h, minrangeset = 21, maxrangeset = 32, trans="rotate270.matrix",
thermal.palette=midgreenpal)
plotTherm(temperature, w=w, h=h, minrangeset = 21, maxrangeset = 32, trans="rotate270.matrix",
thermal.palette=rainbow1234pal)
With thermal imaging analysis, there are at least 7 environmental parameters that must be known to convert raw to temperature. Sometimes, the parameters might have been incorrectly input by the user or changing the parameters is too cumbersome in the commercial software. temp2raw() is the inverse of raw2temp(), which allows you to convert an estimated temperature back to the raw values (i.e. deconvolute), using the initial object parameters used.
For example, convert a temperature estimated at 23 degrees C, under the default blackbody conditions:
temp2raw(23, E=1, OD=0, RTemp=20, ATemp=20, IRWTemp=20, IRT=1, RH=50, PR1=21106.77, PB=1501, PF=1, PO=-7340, PR2=0.012545258)
## [1] 17994.06
Which yields a raw value of 17994.06 (using the calibration constants above). Now you can use raw2temp to calculate a better estimate of an object that has emissivity=0.95, distance=1m, window transmission=0.96, all temperatures=20C, 50 RH:
raw2temp(17994.06, E=0.95, OD=1, RTemp=20, ATemp=20, IRWTemp=20, IRT=0.96, RH=50, PR1=21106.77, PB=1501, PF=1, PO=-7340, PR2=0.012545258)
## [1] 23.31223
Note: the default calibration constants for my FLIR camera will be used if you leave out the calibration data during this two step process, but it is more appropriate to look up your camera’s calibrations constants using the flirsettings() function.
See the following github for an explanation and break-down of the conversion process and comparison to existing commercial software:
https://github.com/gtatters/ThermimageCalibration
Finding a way to quantitatively analyse thermal images in R is a challenge due to limited interactions with the graphics environment. Thermimage has a function that allows you to write the image data to a file format that can be easily imported into ImageJ.
First, the image matrix needs to be transposed (t) to swap the row vs. column order in which the data are stored, then the temperatures need to be transformed to a vector, a requirement of the writeBin function. The function writeFlirBin is a wrapper for writeBin, and uses information on image width, height, frame number and image interval (the latter two are included for thermal video saves) but are kept for simplicity to contruct a filename that incorporates image information required when importing to ImageJ:
writeFlirBin(as.vector(t(temperature)), templookup=NULL, w=w, h=h, I="", rootname="Uploads/FLIRjpg")
The raw file can be found here: https://github.com/gtatters/Thermimage/blob/master/Uploads/FLIRjpg_W640_H480_F1_I.raw?raw=true
The .raw file is simply the pixel data saved in raw format but with real 32-bit precision. This means that the temperature data (negative or positive values) are encoded in 4 byte chunks. ImageJ has a plethora of import functions, and the File–>Import–>Raw option provides great flexibility. Once opening the .raw file in ImageJ, set the width, height, number of images (i.e. frames or stacks), byte storage order (little endian), and hyperstack (if desired):
The image imports clearly just as it would in a thermal image program. Each pixel stores the calculated temperatures as provided from the raw2temp function above.
Importing thermal videos (March 2017: still in development) is a little more involved and less automated. I don’t really recommend using R to work with thermal videos since the memory limitations and speed are not efficient for large video files. It is better to convert videos to individual files and import them frame by frame, or use an ImageJ alternative.
But below are steps that have worked for seq and fcf files tested.
Set file info and extract meta-tags as done above:
# set filename as v
v<-paste0(system.file("extdata/SampleSEQ.seq", package="Thermimage"))
# Extract camera values using Exiftool (needs to be installed)
camvals<-flirsettings(v)
w<-camvals$Info$RawThermalImageWidth
h<-camvals$Info$RawThermalImageHeight
Create a lookup variable to convert the raw binary to actual temperature estimates, use parameters relevant to the experiment. You could use the values stored in the FLIR meta-tags, but these are not necessarily correct for the conditions of interest. suppressWarnings() is used because of NaN values returned for binary values that fall outside the range.
suppressWarnings(
templookup<-raw2temp(raw=1:65536, E=camvals$Info$Emissivity, OD=camvals$Info$ObjectDistance, RTemp=camvals$Info$ReflectedApparentTemperature, ATemp=camvals$Info$AtmosphericTemperature, IRWTemp=camvals$Info$IRWindowTemperature, IRT=camvals$Info$IRWindowTransmission, RH=camvals$Info$RelativeHumidity, PR1=camvals$Info$PlanckR1,PB=camvals$Info$PlanckB,PF=camvals$Info$PlanckF,PO=camvals$Info$PlanckO,PR2=camvals$Info$PlanckR2)
)
plot(templookup, type="l", xlab="Raw Binary 16 bit Integer Value", ylab="Estimated Temperature (C)")
The advantage of using the templookup variable is in its index capacity. For computations involving large files, this is most efficient way to convert the raw binary values rapidly without having to call the raw2temp function repeatedly. Thus, for a raw binary value of 17172, 18273, and 24932:
templookup[c(17172, 18273, 24932)-1]
## [1] 18.30355 24.77367 57.07398
# subtract - 1, since R uses 1 rather than 0 as the base starting index value
We will use the templookup later on, but first to detect where the image frames can be found in the video file. Using the width and height information, we use this to find where in the video file these are stored. This corresponds to reproducible locations in the frame header:
fl<-frameLocates(v, w, h)
n.frames<-length(fl$f.start)
n.frames; fl
## [1] 2
## $h.start
## [1] 320 617372
##
## $f.start
## [1] 2748 619800
The relative positions of the header start (h.start) are 320 and 617372, and the frame start (f.start) positions are 2748 and 619800. The video file is a short, two frame (n.frames) sequence from a thermal video.
Then pass the fl data to two different functions, one to extract the time information from the header, and the other to extract the actual pixel data from the image frame itself. The lapply function will have to be used (for efficiency), but to wrap the function across all possible detected image frames. Note: For large files, the parallel function, mclapply, is advised (?getFrames for an example):
extract.times<-do.call("c", lapply(fl$h.start, getTimes, vidfile=v))
data.frame(extract.times)
## extract.times
## 1 2012-06-13 15:52:08.698-0500
## 2 2012-06-13 15:52:12.665-0500
Interval<-signif(mean(as.numeric(diff(as.POSIXct(extract.times)))),3)
Interval
## [1] 3.97
This particular sequence was actually captured at 0.03 sec intervals, but the sample file in the package was truncated to only two frames to minimise online size requirements for CRAN. At present, the getTimes function might not accurately render the time on the first frame. On the original 100 frame file, it accurately captures the real time stamps, so the error is appears to be how FLIR saves time stamps (save time vs. modification time vs. original time appear highly variable in .seq and .fcf files). Precise time capture is not crucial but is helpful for verifying data conversion.
After extracting times, then extract the frame data, with the getFrames function:
alldata<-unlist(lapply(fl$f.start, getFrames, vidfile=v, w=w, h=h))
class(alldata); length(alldata)/(w*h)
## [1] "integer"
## [1] 2
The raw binary data are stored as an integer vector. length(alldata)/(w*h) verifies the total # of frames in the video file is 2.
It is best to convert the temperature data in the following manner, although depending on file size and system limits, you may wish to delay converting to temperature until writing the file.
alltemperature<-templookup[alldata]
head(alldata)
## [1] 17870 17833 17808 17829 17829 17861
head(alltemperature)
## [1] 22.46279 22.24723 22.10131 22.22390 22.22390 22.41040
I recommend converting the binary and/or temperature variables to a matrix class, where each column represents a separate image frame, while the individual rows correspond to unique pixel positions. Pixels are filled into the row values the same way across all frames. Dataframes and arrays are much slower for processing large files.
alldata<-unname(matrix(alldata, nrow=w*h, byrow=FALSE))
alltemperature<-unname(matrix(alltemperature, nrow=w*h, byrow=FALSE))
dim(alltemperature)
## [1] 307200 2
Frames extracted from thermal vids are upside down, so use the mirror.matrix function inside the plotTherm function.
plotTherm(alltemperature[,1], w=w, h=h, trans="mirror.matrix")
plotTherm(alltemperature[,2], w=w, h=h, trans="mirror.matrix")
These files can be found:
https://github.com/gtatters/Thermimage/blob/master/Uploads/SampleSEQ1.png?raw=true https://github.com/gtatters/Thermimage/blob/master/Uploads/SampleSEQ2.png?raw=true
Now, export entire sequence to a raw bin for opening in ImageJ - smallish file size
writeFlirBin(bindata=alldata, templookup, w, h, Interval, rootname="Uploads/SampleSEQ")
The newly written 32-bit video file (https://github.com/gtatters/Thermimage/blob/master/Uploads/SampleSEQ_W640_H480_F2_I3.97.raw?raw=true) can now be imported into ImageJ, as desribed above for the single image. Each frame is converted into a stack in ImageJ.
Note: 32-bit video files can be large and difficult to load into ImageJ. Approaches involving direct import of flir video files is recommended and under development.
If you have a lot of files and wish simply to analyse images in ImageJ, not in R, then you will want to bulk convert these files. The following methods are available in R, but are based on command line tools that are also described in https://github.com/gtatters/ThermimageBash/blob/master/README.md
https://github.com/gtatters/ThermImageJ/blob/master/SampleFiles.zip
ls SampleFLIR
## SampleFLIR.jpg
## SampleFLIR.png
## SampleFLIRCSQ.csq
## SampleFLIRONE.jpg
## SampleFLIRSEQ.seq
## output
https://github.com/gtatters/Thermimage/blob/master/Uploads/perl.zip
cd ~/IRconvert/scripts
ls
## AVIClean
## CompleteCSQConvert
## CompleteFLIRJPGConvert
## CompleteSEQConvert
## ConcatMP4
## ConvertACQtoTXT
## ConvertCSQtoAVI
## ConvertFCFtoAVI
## ConvertFLIRJPG.sh
## ConvertFLIRJPGtoRAW
## ConvertFLIRJPGtoTIFF
## ConvertFLIRJPGtoTIFFbyline
## ConvertFLIRRAWtoTIFF
## ConvertSEQtoAVI
## ConverttoGrayscale
## Detecting Frozen Frames.docx
## ExtractAllFLIRJPGs
## FFFTimeStamps
## FLIRFocalDistance
## FLIRFrozenFrameDetect
## FLIRFrozenFrameExtracts.pl
## FLIRMedianRangeExtracts.pl
## FrameDifference
## IRFileImport.R
## OldFiles
## RenumberFiles
## Sample Exiftool Commands.docx
## convertcsq.pl
## ffmpegscript
## flirclean.pl
## imagejscript_rad2temp
## scrapcode
## split.pl
## ~$iftool commands.docx
Bulk FLIR jpg file:
library(Thermimage)
exiftoolpath <- "installed"
f<-paste0("SampleFLIR/SampleFLIR.jpg")
# if JPG contains raw thermal image as TIFF, endian = "lsb"
# if JPG contains raw thermal image as PNG, endian = "msb"?
vals<-flirsettings(f)
w<-vals$Info$ImageWidth
h<-vals$Info$ImageHeight
res.in<-paste0(w,"x",h)
if(vals$Info$RawThermalImageType=="PNG") endian="msb"
if(vals$Info$RawThermalImageType=="TIFF") endian="lsb"
convertflirJPG(f, exiftoolpath="installed", res.in=res.in, endian=endian, outputfolder="", verbose=FALSE)
cat("\n")
Converted files are in the output subfolder
Here is a sample image:
The above PNG file is a sample image of the 16 bit grayscale image. Although it looks washed out, it can be imported into ImageJ and the Brightness/Contrast changed for optimal viewing.
Convert FLIR csq file
library(Thermimage)
setwd("/Users/GlennTattersall/Documents/GitHub/ThermimageProjects/Thermimage/SampleFLIR")
exiftoolpath <- "installed"
perlpath <- "installed"
f<-"SampleFLIRCSQ.csq"
# if JPG contains raw thermal image as TIFF, endian = "lsb"
# if JPG contains raw thermal image as PNG, endian = "msb"
vals<-flirsettings(f)
w<-vals$Info$RawThermalImageWidth
h<-vals$Info$RawThermalImageHeight
res.in<-paste0(w,"x",h)
convertflirVID(f, exiftoolpath="installed", perlpath="installed",
fr=30, res.in=res.in, res.out=res.in, outputcompresstype="jpegls", outputfilenameroot=NULL,
outputfiletype="avi", outputfolder="./output", verbose=FALSE)
##
## ffmpeg -r 30 -f image2 -vcodec jpegls -s 1024x768 -i 'temp/frame%05d.jpegls' -vcodec jpegls -s 1024x768 './output/SampleFLIRCSQ.csq.avi' -y
Converted files are in an output subfolder
The above PNG file is a sample image of the 16 bit grayscale image.
Although it looks washed out, it can be imported into ImageJ and the
Brightness/Contrast changed for optimal viewing.
The information below is duplicated at: https://github.com/gtatters/Thermimage/blob/master/HeatTransferCalculations.md
Before getting started ensure you have the following information available:
If missing ground temperature (Tg) information, we have derived a relationship based on empirical data collected using thermal imaging in Galapagos that describes Tg as a function of Ta and Solar Radiation:
Tg-Ta \~ Se, (N=516, based on daytime measurements)
Range of Ta: 23.7 to 34 C. Range of SE: 6.5 to 1506.0 Watts/m^2
which yielded the following relationship:
Tg = 0.0187128*SE + Ta
Alternatively, published work by Bartlett et al. (2006) in the Tground() function, found the following relationship:
Tg = 0.0121*SE + Ta
Incoming infrared radiation is modelled as deriving from two sources: sky (Ld) and ground (Lu). Half of the incoming is assumed to be from the sky and half from the ground. Sky radiation is influenced by cloud cover, cloud emissivity, and sky temperature, ground radiation is influenced by ground temperature. The two functions Ld() and Lu() estimate these sources of radiation.
Wind speed should be measured but is usually highly variable when measured. One alternative is to model it under different scenarios. Free convection is applied in still air (wind speed = 0). Forced convection is for wind speed > 0.
It might be sufficient to model convection in low air flow conditions (<=0.1 m/s) using forced convection with wind speed set to 0.1.
The shape is determined by the user, estimating the best approximation
of sphere, cylinder, or plate.
The convection parameters are highlighted in references contained in
Thermimage, but can be found in Gates (2003) Biophysical Ecology.
Once you have decided on what variables you have or need to model, create a data frame with these values (Ta, Ts, Tg, SE, A, L, Shape, rho), where each row corresponds toan individual measurement. The data frame is not required for calling functions, but it will force you to assemble your data and find missing values before proceeding with calculations.
Other records such as size, date image captured, time of day, species, sex, etc…should also be stored in the data frame.
Here is a random data set:
Ta<-rnorm(20, 25, sd=10)
Ts<-Ta+rnorm(20, 5, sd=1)
RH<-rep(0.5, length(Ta))
SE<-rnorm(20, 400, sd=50)
Tg<-Tground(Ta,SE)
A<-rep(0.4,length(Ta))
L<-rep(0.1, length(Ta))
V<-rep(1, length(Ta))
shape<-rep("hcylinder", length(Ta))
c<-forcedparameters(V=V, L=L, Ta=Ta, shape=shape)$c
n<-forcedparameters(V=V, L=L, Ta=Ta, shape=shape)$n
a<-freeparameters(L=L, Ts=Ts, Ta=Ta, shape=shape)$a
b<-freeparameters(L=L, Ts=Ts, Ta=Ta, shape=shape)$b
m<-freeparameters(L=L, Ts=Ts, Ta=Ta, shape=shape)$m
type<-rep("forced", length(Ta))
rho<-rep(0.1, length(Ta))
cloud<-rep(0, length(Ta))
d<-data.frame(Ta, Ts, Tg, SE, RH, rho, cloud, A, V, L, c, n, a, b, m, type, shape)
head(d)
## Ta Ts Tg SE RH rho cloud A V L c n a
## 1 20.41558 24.84622 25.55637 424.8590 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 2 29.51272 37.37743 34.69060 427.9246 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 3 23.43464 26.91547 29.24873 480.5039 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 4 18.77888 23.64169 23.15669 361.8029 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 5 28.43642 33.33917 33.11920 387.0064 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 6 14.66700 17.54296 19.87179 430.1481 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## b m type shape
## 1 0.58 0.25 forced hcylinder
## 2 0.58 0.25 forced hcylinder
## 3 0.58 0.25 forced hcylinder
## 4 0.58 0.25 forced hcylinder
## 5 0.58 0.25 forced hcylinder
## 6 0.58 0.25 forced hcylinder
The basic approach to estimating heat loss is based on that outlined in Tattersall et al (2009) and Tattersall et al (2017). The approach involves breaking the object into component shapes, deriving the exposed areas of those shapes empirically, and calcuating Qtotal for each shape:
(Qtotal<-qrad() + qconv()) # units are in W/m2
## [1] -186.8849
Notice how the above example yielded an estimate. This is because there are defaultvalues in all the functions. In this case, the estimate is negative, meaning a net loss of heat to the environment. It’s units are in W/m2.
To convert the above measures into total heat flux, the Area (m2) of each part is required. This is the largest source of error in any morphometric analysis and beyond the scope of this package.
Area1<-0.2 # units need to be in m2
Area2<-0.3 # units need to be in m2
(Qtotal1<-qrad()*Area1 + qconv()*Area1)
## [1] -37.37699
(Qtotal2<-qrad()*Area2 + qconv()*Area2)
## [1] -56.06548
(QtotalAll<-Qtotal1 + Qtotal2)
## [1] -93.44246
If used comprehensively across the entire body’s thermal image, component shapes should sum to estimate entire body heat exchange: WholeBody = Qtotal1 + Qtotal2 + Qtotal3 … Qtotaln
qrad is the net radiative heat flux (W/m2).
qconv is the net convective heat flux (W/m2)
conductive heat flux (W/m2), or qcond is often ignored unless a large contact area exists between substrate.
Additional information is required to accurately calculate conductive heat exchange and are not provided here, since thermal imaging would not capture the temperature.
qabs = absorbed radiation (W/m2). Radiation is both absorbed and emitted
by animals. I have broken this down into partially separate functions.
qabs() is a function to estimate the area specific amount of solar and
infrared radiation absorbed by the object from the environment and
requires information on the air (ambient) temperature, ground
temperature, relative humidity, emissivity of the object, reflectivity
of the object, proportion cloud cover, and solar energy.
qabs(Ta = 20, Tg = NULL, RH = 0.5, E = 0.96, rho = 0.1, cloud = 0, SE = 400)
## [1] 720.2545
compare to a shaded environment with lower SE, which yields a much lower value:
qabs(Ta = 20, Tg = NULL, RH = 0.5, E = 0.96, rho = 0.1, cloud = 0, SE = 100)
## [1] 440.2954
qrad = net radiative heat flux (includes that absorbed and that emitted). Since the animal also emits radiation, qrad() provides the net radiative heat transfer. Here is an example, using the same parameters as the previous example, but calculating qrad based on a Ts=27 degrees C:
qrad(Ts = 27, Ta = 20, Tg = NULL, RH = 0.5, E = 0.96, rho = 0.1, cloud = 0, SE = 100)
## [1] -1.486309
Notice how the absorbed environmental radiation is \~440 W/m2, but the animal is also losing a similar amount, so once we account for the net radiative flux, it very nearly balances out at a slightly negative number (-1.486 W/m2)
If you have measured ground temperature, then simply include it in the call to qrad:
qrad(Ts = 30, Ta = 25, Tg = 28, RH = 0.5, E = 0.96, rho = 0.1, cloud = 0, SE = 100)
## [1] 14.29534
If you do not have ground temperature, but have measured Ta and SE, then set Tg=NULL. This will force a call to the Tground() function to estimate Tground. It is likely better to assume that Tground is slightly higher than Ta, at least in the daytime. If using measurements obtained at night (SE=0), then you will have to provide both Ta and Tground, since Tground could be colder equal to Ta depending on cloud cover.
This is simply the convective heat coefficient, which depends on wind speed and your modelled mode of convective heat exchange (free or forced). This is used in calculating the convective heat transfer and/or operative temperature but usually you will not need to call hconv() yourself
This is the function to calculate area specific convective heat transfer, analagous to qrad, except for convective heat transfer. Positive values mean heat is gained by convection, negative values mean heat is lost by convection. Included in the function is the ability to estimate free convection (which occurs at 0 wind speed) or forced convection (wind speed >=0.1 m/s). Unless working in a completely still environment, it is more appropriate to used “forced” convection down to 0.1 m/s wind speed (see Gates Biophysical Ecology).
Typical wind speeds indoors are likely <0.5 m/s, but outside can vary wildly.
In addition to needing surface temperature, air temperature, and velocity, you need information/estimates on shape. L is the critical dimension of the shape, which is usually the height of an object within the air stream. The diameter of a horizontal cylinder is its critical dimension. Finally, shape needs to be assigned. see help(qconv) for details.
Some examples:
qconv(Ts = 30, Ta = 20, V = 1, L = 0.1, type = "forced", shape="hcylinder")
## [1] -102.6565
qconv(Ts = 30, Ta = 20, V = 1, L = 0.1, type = "forced", shape="hplate")
## [1] -124.323
qconv(Ts = 30, Ta = 20, V = 1, L = 0.1, type = "forced", shape="sphere")
## [1] -186.3256
notice how the horizontal cylinder loses less than the horizontal plate which loses less than the sphere. Spherical objects lose \~1.8 times as much heat per area as cylinders.
Take a convection estimate at low wind speed:
qconv(Ts = 30, Ta = 20, V = 0.1, L = 0.1, type = "forced", shape="hcylinder")
## [1] -32.58495
compare to a radiative estimate (without any solar absorption):
qrad(Ts = 30, Ta = 20, Tg = NULL, RH = 0.5, E = 0.96, rho = 0.1, cloud = 0, SE = 0)
## [1] -112.6542
In this case, the net radiative heat loss is greater than convective heat loss if you decrease the critical dimension, however, the convective heat loss per m2 is much greater. This is effectively how convective exchange works: small objects lose heat from convection more readily than large objects (e.g. think about frostbite that occurs on fingers and toes)
If L is 10 times smaller:
qconv(Ts = 30, Ta = 20, V = 0.1, L = 0.01, type = "forced", shape="hcylinder")
## [1] -111.4338
qrad(Ts = 30, Ta = 20, Tg = NULL, RH = 0.5, E = 0.96, rho = 0.1, cloud = 0, SE = 0)
## [1] -112.6542
convection and radiative heat transfer are nearly the same.
A safe conclusion here is that larger animals would rely more on radiative heat transfer than they would on convective heat transfer
Ideally, you have all parameters estimated or measured and put into a data frame. Using the dataframe, d we constructed earlier
(qrad.A<-with(d, qrad(Ts, Ta, Tg, RH, E=0.96, rho, cloud, SE)))
## [1] 316.5873 297.2482 374.0562 255.4255 277.9465 330.5551 283.1776 226.6077
## [9] 305.0609 263.9476 193.0314 272.0463 210.1643 368.5207 235.2521 257.8783
## [17] 320.5913 247.2342 215.1916 333.1351
(qconv.free.A<-with(d, qconv(Ts, Ta, V, L, c, n, a, b, m, type="free", shape)))
## [1] -17.52238 -35.75827 -12.94160 -19.70059 -19.81552 -10.24065 -16.83840
## [8] -22.29188 -23.35566 -19.18085 -22.97243 -24.48561 -21.60582 -20.51785
## [15] -20.41304 -22.62516 -12.64327 -20.91026 -24.50114 -15.65868
(qconv.forced.A<-with(d, qconv(Ts, Ta, V, L, c, n, a, b, m, type, shape)))
## [1] -45.46022 -79.85905 -35.58598 -49.99564 -49.84079 -29.72594 -43.74322
## [8] -54.83852 -57.44223 -48.08360 -56.00923 -59.37027 -53.10776 -51.35088
## [15] -50.56298 -55.78882 -34.92138 -52.12383 -59.07566 -41.18521
qtotal<-A*(qrad.A + qconv.forced.A) # Multiply by area to obtain heat exchange in Watts
d<-data.frame(d, qrad=qrad.A*A, qconv=qconv.forced.A*A, qtotal=qtotal)
head(d)
## Ta Ts Tg SE RH rho cloud A V L c n a
## 1 20.41558 24.84622 25.55637 424.8590 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 2 29.51272 37.37743 34.69060 427.9246 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 3 23.43464 26.91547 29.24873 480.5039 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 4 18.77888 23.64169 23.15669 361.8029 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 5 28.43642 33.33917 33.11920 387.0064 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## 6 14.66700 17.54296 19.87179 430.1481 0.5 0.1 0 0.4 1 0.1 0.174 0.618 1
## b m type shape qrad qconv qtotal
## 1 0.58 0.25 forced hcylinder 126.6349 -18.18409 108.45083
## 2 0.58 0.25 forced hcylinder 118.8993 -31.94362 86.95566
## 3 0.58 0.25 forced hcylinder 149.6225 -14.23439 135.38810
## 4 0.58 0.25 forced hcylinder 102.1702 -19.99825 82.17193
## 5 0.58 0.25 forced hcylinder 111.1786 -19.93632 91.24227
## 6 0.58 0.25 forced hcylinder 132.2220 -11.89038 120.33165
Toucan Proximal Bill data at 10 degrees (from Tattersall et al 2009 spreadsheet calculations)
A<-0.0097169
L<-0.0587
Ta<-10
Tg<-Ta
Ts<-15.59
SE<-0
rho<-0.1
E<-0.96
RH<-0.5
cloud<-1
V<-5
type="forced"
shape="hcylinder"
(qrad.A<-qrad(Ts=Ts, Ta=Ta, Tg=Tg, RH=RH, E=E, rho=rho, cloud=cloud, SE=SE))
## [1] -37.90549
compare to calculated value of -28.7 W/m2 the R calculations differ slightly from Tattersall et al (2009) since they did not use estimates of longwave radiation (Ld and Lu), but instead assumed a simpler, constant Ta.
(qrad.A<-qrad(Ts=Ts, Ta=Ta, Tg=Tg, RH=RH, E=E, rho=rho, cloud=0, SE=SE))
## [1] -83.03191
but if cloud = 0, then the qrad values calculated here are much higher than calculated by Tattersall et al (2009) since they only estimated under simplifying, indoor conditions where background temperature = air temperature. In the outdoors, then, cloud presence would affect estimates of radiative heat loss.
(qconv.forced.A<-qconv(Ts, Ta, V, L, type=type, shape=shape))
## [1] -192.7086
compare to calculated value of -191.67 W/m2 - which is really close! The
difference lies in estimates of air kinematic viscosity used.
Total area specific heat loss for the proximal area of the bill
(Watts/m2)
(qtotal.A<-(qrad.A + qconv.forced.A))
## [1] -275.7405
Total heat exchange from the bill, including convective and radiative is:
qtotal.A*A
## [1] -2.679343
Total heat loss for the proximal area of the bill (Watts) can be as much
as 2.6 Watts!
This lines up well with the published values in Tattersall et al (2009).
This was confirmed in van de Van (2016) where they recalculated the area
specific heat flux from toucan bills to be \~65 W/m2, but they used free
convection estimates and so wind speed of 0 significantly reduces the
estimated convective heat exchange:
qrad(Ts=Ts, Ta=Ta, Tg=Tg, RH=0.5, E=0.96, rho=rho, cloud=1, SE=0) + qconv(Ts, Ta, V, L, type="free", shape=shape)
## [1] -64.83292
Operative environmental temperature is the expression of the “effective temperature” an object is experiencing, accounting for heat absorbed from radiation and heat lost to convection.
In other words, it is often used by some when trying to predict animal body temperature as a null expectation or reference point to determine whether active thermoregulation is being used. More often used in ectotherm studies, but as an initial estimate of what a freely moving animal temperature would be, it serves a useful reference.
Usually, people would measure operative temperature with a model of an object placed into the environment, allowing wind, solar radiation and ambient temperature to influence its temperature. There are numerous formulations for it. The one here is from Angilletta’s book on Thermal Adaptations, and requires measurements of air temperature, ground temperature, SE, wind speed, relative humidity, emissivity, reflectance, cloud cover, and object shape and size.
Note: in the absence of sun or wind, operative temperature is simply ambient temperature.
Ts<-40
Ta<-30
SE<-seq(0,1100,100)
Toperative<-NULL
for(rho in seq(0, 1, 0.1)){
temp<-Te(Ts=Ts, Ta=Ta, Tg=NULL, RH=0.5, E=0.96, rho=rho, cloud=1, SE=SE, V=1,
L=0.1, type="forced", shape="hcylinder")
Toperative<-cbind(Toperative, temp)
}
rho<-seq(0, 1, 0.1)
Toperative<-data.frame(SE=seq(0,1100,100), Toperative)
colnames(Toperative)<-c("SE", seq(0,1,0.1))
matplot(Toperative$SE, Toperative[,-1], ylim=c(25, 50), type="l", xlim=c(0,1000),
main="Effects of Altering Reflectance from 0 to 1",
ylab="Operative Temperature (°C)", xlab="Solar Radiation (W/m2)", lty=1,
col=flirpal[rev(seq(1,380,35))])
for(i in 2:12){
ymax<-par()$yaxp[2]
xmax<-par()$xaxp[2]
x<-Toperative[,1]; y<-Toperative[,i]
lm1<-lm(y~x)
b<-coefficients(lm1)[1]; m<-coefficients(lm1)[2]
if(max(y)>ymax) {xpos<-(ymax-b)/m; ypos<-ymax}
if(max(y)<ymax) {xpos<-xmax; ypos<-y[which(x==1000)]}
text(xpos, ypos, labels=rho[(i-1)])
}
Ts<-40
Ta<-30
SE<-seq(0,1100,100)
Toperative<-NULL
V<-c(0.1,1,2,3,4,5,6,7,8,9,10)
for(V in V){
temp<-Te(Ts=Ts, Ta=Ta, Tg=NULL, RH=0.5, E=0.96, rho=0.1, cloud=1, SE=SE, V=V,
L=0.1, type="forced", shape="vcylinder")
Toperative<-cbind(Toperative, temp)
}
V<-seq(0,10,1)
Toperative<-data.frame(SE=seq(0,1100,100), Toperative)
colnames(Toperative)<-c("SE", seq(0,10,1))
matplot(Toperative$SE, Toperative[,-1], ylim=c(30, 50), type="l", xlim=c(0,1000),
main="Effects of Altering Wind Speed from 0 to 10 m/s",
ylab="Operative Temperature (°C)", xlab="Solar Radiation (W/m2)", lty=1,
col=flirpal[rev(seq(1,380,35))])
for(i in 2:12){
ymax<-par()$yaxp[2]
xmax<-par()$xaxp[2]
x<-Toperative[,1]; y<-Toperative[,i]
lm1<-lm(y~x)
b<-coefficients(lm1)[1]; m<-coefficients(lm1)[2]
if(max(y)>ymax) {xpos<-(ymax-b)/m; ypos<-ymax}
if(max(y)<ymax) {xpos<-xmax; ypos<-y[which(x==1000)]}
text(xpos, ypos, labels=V[(i-1)])
}
Ts<-40
Ta<-30
SE<-seq(0,1100,100)
Toperative<-NULL
for(RH in seq(0, 1, 0.5)){
temp<-Te(Ts=Ts, Ta=Ta, Tg=NULL, RH=RH, E=0.96, rho=0.1, cloud=0.5, SE=SE, V=1,
L=0.1, type="forced", shape="hcylinder")
Toperative<-cbind(Toperative, temp)
}
RH<-seq(0, 1, 0.5)
Toperative<-data.frame(SE=seq(0,1100,100), Toperative)
colnames(Toperative)<-c("SE", seq(0,1,0.5))
matplot(Toperative$SE, Toperative[,-1], ylim=c(30, 50), type="l", xlim=c(0,1000),
main="Effects of changing RH from 0 to 1",
ylab="Operative Temperature (°C)", xlab="Solar Radiation (W/m2)", lty=1,
col=flirpal[rev(seq(1,380,35))])
for(i in 2:3){
ymax<-par()$yaxp[2]
xmax<-par()$xaxp[2]
x<-Toperative[,1]; y<-Toperative[,i]
lm1<-lm(y~x)
b<-coefficients(lm1)[1]; m<-coefficients(lm1)[2]
if(max(y)>ymax) {xpos<-(ymax-b)/m; ypos<-ymax}
if(max(y)<ymax) {xpos<-xmax; ypos<-y[which(x==1000)]}
text(xpos, ypos, labels=RH[(i-1)])
}
Ts<-40
Ta<-30
SE<-seq(0,1100,100)
Toperative<-NULL
for(cloud in seq(0, 1, 0.5)){
temp<-Te(Ts=Ts, Ta=Ta, Tg=NULL, RH=0.5, E=0.96, rho=0.5, cloud=cloud, SE=SE, V=1,
L=0.1, type="forced", shape="hcylinder")
Toperative<-cbind(Toperative, temp)
}
cloud<-seq(0, 1, 0.5)
Toperative<-data.frame(SE=seq(0,1100,100), Toperative)
colnames(Toperative)<-c("SE", seq(0,1,0.5))
matplot(Toperative$SE, Toperative[,-1], ylim=c(30, 50), type="l", xlim=c(0,1000),
main="Effects of changing cloud cover from 0 to 1",
ylab="Operative Temperature (°C)", xlab="Solar Radiation (W/m2)", lty=1,
col=flirpal[rev(seq(1,380,35))])
for(i in 2:3){
ymax<-par()$yaxp[2]
xmax<-par()$xaxp[2]
x<-Toperative[,1]; y<-Toperative[,i]
lm1<-lm(y~x)
b<-coefficients(lm1)[1]; m<-coefficients(lm1)[2]
if(max(y)>ymax) {xpos<-(ymax-b)/m; ypos<-ymax}
if(max(y)<ymax) {xpos<-xmax; ypos<-y[which(x==1000)]}
text(xpos, ypos, labels=cloud[(i-1)])
}
Angiletta, M. J. 2009. Thermal Adaptation: A Theoretical and Empirical Synthesis. Oxford University Press, Oxford, UK, 304 pp. Gates, D.M.
Blaxter, 1986. Energy metabolism in animals and man. Cambridge University Press, Cambridge, UK, 340 pp.
Gates, DM. 2003. Biophysical Ecology. Dover Publications, Mineola, New York, 611 pp.
Tattersall, GJ, Andrade, DV, and Abe, AS. 2009. Heat exchange from the toucan bill reveals a controllable vascular thermal radiator. Science, 325: 468-470.
Tattersall GJ, Chaves JA, Danner RM. Thermoregulatory windows in Darwin’s finches. Functional Ecology 2017; 00:1–11. https://doi.org/10.1111/1365-2435.12990
The following open source programs and programmers were critical to the development of Thermimage.
Imagemagick: http://imagemagick.org
Perl: http://www.perl.org
raw2temp, temp2raw: https://github.com/gtatters/ThermimageCalibration
EEVBlog:
raw to temperature conversion: http://u88.n24.queensu.ca/exiftool/forum/index.php?topic=4898.135
magicbyte import: http://u88.n24.queensu.ca/exiftool/forum/index.php?topic=4898.0
fileformat: https://www.eevblog.com/forum/thermal-imaging/csq-file-format/
2020-08-20: Version 4.1.2 is on Github (development version) - added error warning when trying to load a non-radiometric image file with readflirjpg. See issues #7, #10, #13.