gw-vis kagra-vis issues

gw-vis / kagra-vis

Task management for VIS subgroup.

1 stars 0 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Check the location of the stepper motors on IP stage

#89 MiyoKouseki closed 3 years ago
12
Decide if we use the PF actuator

#88 MiyoKouseki closed 3 years ago
1
LVDT card recovery document and related topics.

#87 MiyoKouseki opened 4 years ago
1
Change the way to bind cables between the payload and BF

#86 MiyoKouseki closed 3 years ago
9
Type-B work TO DO list

#85 naibafomsare opened 4 years ago
3
Adjustment of IM and BF ballast mass in SR3 suspension due to fishing rod failure

#84 naibafomsare opened 4 years ago
1
Prepare the IP fixing jig

#83 Ryutaro-T opened 4 years ago
5
ToDo List for O4

#82 MiyoKouseki closed 4 years ago
1
how do we switch the coil driver from HPCD to LPCD

#80 MiyoKouseki opened 4 years ago
0
Installation of the new electronics (SG card, LVDT combiner, RS monitor)

#65 MiyoKouseki closed 4 years ago
2
Modofication of the IMMT2 suspension

#64 MiyoKouseki opened 4 years ago
3
Installation of the better OpLev covers

#63 MiyoKouseki closed 4 years ago
0
Installation of additional beams for the outer frame

#62 MiyoKouseki closed 4 years ago
2
Gluing of the suspension wire in PR3

#61 MiyoKouseki opened 4 years ago
4
Replacement of the in-vac cable for the traversor in PR3

#60 MiyoKouseki opened 4 years ago
3
Replacement of the damaged PTFE cable in ETMY

#59 MiyoKouseki opened 4 years ago
2
Fixing of the In-vac D-Sub connectors around the IP in ETMY

#58 MiyoKouseki opened 4 years ago
3
Cleaning of the LVDT-ACT units in BS

#56 MiyoKouseki opened 4 years ago
2
Inspection of the BF condition in SRM

#55 MiyoKouseki opened 4 years ago
0
Adjustment of F1 keystone postion with ballast mass due to fishing rod failure in BS suspension

#54 MiyoKouseki opened 4 years ago
4
Installation of the yaw stepper motor in BS

#53 MiyoKouseki opened 4 years ago
1
Installation of the heater jacket around the chamber in Type-A

#51 MiyoKouseki closed 4 years ago
1
Installation of the geophones or better ACCs in Type-A

#50 MiyoKouseki opened 4 years ago
5
Replacement of the F0 blades in ITMX/ITMY

#49 MiyoKouseki opened 4 years ago
2
Disassembling procedure of ETMY

#67 MiyoKouseki closed 3 years ago
5
Decide on suitable adjustment methods which should be applied for all suspensions

#68 MiyoKouseki closed 4 years ago
3
Enable IP stepper motor limit switches which only require software additionsA34

#69 MiyoKouseki closed 4 years ago
1
Survey all LDVT drivers and measure values of their resistances

#70 MiyoKouseki opened 4 years ago
0
Test of modified ACC at the site

#72 MiyoKouseki closed 4 years ago
2
New beams in the BS chamber (Mirapro)

#73 MiyoKouseki opened 4 years ago
3
Thermal control + Auto offloading system

#78 MiyoKouseki closed 4 years ago
1
New oplev covers

#79 MiyoKouseki opened 4 years ago
4
New LVDT combiner

#74 MiyoKouseki opened 4 years ago
3
Signal generator cards for the LVDT driver

#77 MiyoKouseki opened 4 years ago
3
Test of additional filters for the LVDT combiner

#76 MiyoKouseki closed 4 years ago
2
Decide on suitable adjustment methods which should be applied for all suspensions and write documentation

#48 MiyoKouseki opened 4 years ago
3
Survey all LDVT drivers and measure values of their resistances.

#46 MiyoKouseki opened 4 years ago
1
Retrieve information about the status of fishing rods

#45 MiyoKouseki opened 4 years ago
0
Install the modified accelerometers on Type-A suspensions

#43 MiyoKouseki opened 4 years ago
0
Install new beams in the BS chamber

#42 MiyoKouseki closed 4 years ago
2
New Oplev covers

#40 MiyoKouseki closed 4 years ago
0
Additional filters for the LVDT combiner.

#39 MiyoKouseki closed 4 years ago
2
Release sensor monitor

#38 MiyoKouseki closed 4 years ago
0
Signal generator cards for the LVDT driver

#37 MiyoKouseki closed 4 years ago
0
Control system upgrade #2: Sensor correction optimization.

#34 MiyoKouseki opened 4 years ago
2
(My dream) Data analysis pipeline for automatic model fitting using simulated models.

#33 MiyoKouseki opened 4 years ago
6
Control system upgrade #1: Optimal control (H2 Hinf optimal controllers and complementary filters).

#32 MiyoKouseki opened 4 years ago
0
(Another dream) One-click optimization of suspension controls, including control matrices, filters and all.

#26 MiyoKouseki opened 4 years ago
0
Preparation of digital system for new accelerometer

#21 MiyoKouseki closed 4 years ago
4
No DC cut filter in the filterbanks of Type-A

#19 MiyoKouseki closed 4 years ago
1