icebreaker-fpga icebreaker issues

icebreaker-fpga / icebreaker

Small and low cost FPGA educational and development board

577 stars 75 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Power input and external pins?

#56 madding1602 opened 1 year ago
0
Add 64 pin variant.

#55 ahmedcharles closed 2 years ago
3
Clean up the design.

#54 ahmedcharles closed 2 years ago
4
Add COPI/CIPO legend to schematics

#53 esden opened 2 years ago
1
Explain CDONE/CRESET.

#52 ahmedcharles closed 2 years ago
1
outdated RGBPanel link on https://www.crowdsupply.com/1bitsquared/icebreaker-fpga

#51 marcmerlin closed 2 years ago
1
Icebreaker v1.0e -- diodes D1 and D11 are shorted

#50 71GA closed 2 years ago
5
Add iCEBreaker Bitsy v1.1c

#49 jordiorlando closed 2 years ago
0
Reset button on icebreaker

#48 smunaut opened 3 years ago
0
USB-C connector

#47 dotcypress closed 1 year ago
0
Bitsy v1.1a

#46 jordiorlando closed 4 years ago
0
Wrong part number

#45 fnsangiul opened 4 years ago
0
iCEBreaker bitsy v1.0a

#44 jordiorlando closed 4 years ago
1
SPI flash and FT2232H signal contention during the USB enumeration process

#43 Disasm opened 4 years ago
1
Too much load on the SRAM slave select line on the bitsy

#42 vr2045 closed 4 years ago
3
FPGA Pin numbers of SPI IO0/IO1 on the diagram are swapped

#41 smunaut closed 2 years ago
2
"J20 Flash" header - add single-row PMOD option?

#40 fm4dd closed 4 years ago
2
Seamless integration of ICEbreaker to Arduino IDE (using soft core)

#39 Harvie opened 4 years ago
3
Frequency accuracy of the 12 MHz oscillator (U7)

#38 andrsmllr closed 4 years ago
2
Fix the schematic to adjust WS2812 ear resistor values

#37 esden opened 5 years ago
0
Need to document the user hacks.

#36 kbob opened 5 years ago
2
Consider adding suggested part numbers for suitable RGB leds to the doco

#35 TomKeddie closed 5 years ago
2
Update README

#34 Ryangwaite closed 5 years ago
1
icebreaker-fpga shipped with Pmods need assembly hints

#33 csylvain opened 5 years ago
1
Fix ice40 RGB schematic symbol pinout

#32 esden closed 5 years ago
1
Fix ice40 model name in schematic

#31 esden closed 5 years ago
0
Extend pads of RGB led foot print a bit to make hand solder easier

#30 smunaut closed 5 years ago
0
Solderpaste V1.0d for C32, C33 and RBG LED

#29 tinyledmatrix closed 5 years ago
1
Change the AUX CS jumper to Normally Closed

#28 esden closed 5 years ago
3
Sync FIFO mode support

#27 smunaut closed 4 years ago
3
Replace diode footprint with SOD−523

#26 esden closed 5 years ago
0
Add Bill of Materials

#25 stv0g closed 5 years ago
2
Add via in pad to the USB footprint to anchor the pads better to the PCB

#24 esden closed 2 years ago
7
PMOD connector 3D model error

#23 DanSGiesbrecht closed 5 years ago
7
RGB LED colours are swapped

#22 miek closed 5 years ago
1
Label PMOD pins on snap-off board

#21 kbob closed 6 years ago
2
Consider adding RAM to the iCEBreaker

#20 esden opened 6 years ago
0
Add unpapulated QSPI RAM footprint

#19 esden closed 6 years ago
5
Add another CS line from FTDI to the iCE40 to use SPI comm from host -> fpga

#18 smunaut closed 6 years ago
2
Adjust footprint to match new buttons

#17 esden closed 6 years ago
0
Add test point for access to FT2232H VREGOUT +1V8 for Powering VCCIO2…

#16 RossBencina closed 5 years ago
1
Add Access to FT2232H VREGOUT +1V8 for Powering VCCIO2

#15 RossBencina closed 6 years ago
3
Explore options for FTDI replacement

#14 esden opened 6 years ago
46
Add FTDI chip flash as mandatory and unique serial numbers

#13 esden closed 6 years ago
1
Mark the FTDI flash as optional/DNP

#12 esden closed 6 years ago
2
Remove bypass of the VCCIO2 jumper.

#11 esden closed 6 years ago
0
Add pullup/pulldown resistors to the unused FTDI RS232 input pins

#10 cliffordwolf closed 6 years ago
0
Add jumper for CRESET

#9 cliffordwolf closed 6 years ago
0
Add USB breakout pads

#8 esden closed 6 years ago
1
Can you add HyperRam ?

#7 mirecta closed 6 years ago
13