josefprusa PrusaMendel issues

josefprusa / PrusaMendel

My own RepRap Mendel redesign

prusa-mendel

367 stars 632 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

MMU2S with Mk3S idler homing not working after firmware update. A solution!

#70 hjvooijen opened 6 months ago
0
golang make

#69 mo5h closed 10 years ago
0
LM8UU x-end-idler.stl Slicing Errors

#68 apapdev007 opened 10 years ago
0
Not able to download

#67 bobbilikr opened 10 years ago
0
Fixed a bug with the screw_hole_spacing parameter on sanguinololu-holder

#66 arnoudja opened 11 years ago
0
ThingDoc submodule points to prusajr repo, where it doesn't exist

#65 mohag opened 11 years ago
1
Wade's Big Gear - Adjust the nut trap to 13.3mm (because 8mm hex nuts ha...

#64 pawl closed 12 years ago
1
X idler/motor brackets should accomodate use of bolts

#63 bgamari closed 12 years ago
3
X End Motor Pulley Alignment Problem

#62 pawl opened 12 years ago
2
Add Printed Parts to reprap.tdoc

#61 pawl opened 12 years ago
0
Add rods to common.tdoc

#60 pawl opened 12 years ago
1
Add Printed Parts to reprap.tdoc

#59 pawl closed 12 years ago
1
Update docs/bill-of-materials.txt - Add Rod Lengths

#58 pawl closed 12 years ago
1
M3 nut diameter incorrect

#57 pawl closed 12 years ago
1
Greg's Wade Reloaded

#56 pawl opened 12 years ago
2
Endstop Holders Allow Too Much Play

#55 pawl opened 12 years ago
0
Update docs/bill-of-materials.txt

#54 pawl closed 12 years ago
1
Mantainence & deprecation fixes

#53 felipesanches opened 12 years ago
0
Bed drilling template for lm8uu wrong

#52 metzench closed 12 years ago
3
Z couplers should be symetrically

#51 jglauche closed 12 years ago
2
bar-clamp hole is too small

#50 hurzl opened 12 years ago
1
X end channels for Z rod could be made smaller

#49 jglauche closed 12 years ago
1
smooth_bar_diameter = 0; Wrong spelling must be your czech "i"

#48 josh13 closed 12 years ago
3
LM8UU & LME8UU stl's the same!

#47 indieflow closed 12 years ago
12
Merge updated zip-tie linear holders and add files for lme8uu linear bearings

#46 jglauche closed 12 years ago
0
BOM is far from complete

#45 Shaun1 closed 2 years ago
2
m8 nut diameter in metric.scad is wrong

#44 triffid opened 12 years ago
2
Remove STLs from repository

#43 brad opened 12 years ago
8
Faceboximages

#42 brad opened 12 years ago
0
Makeexec

#41 brad opened 12 years ago
0
nema 17 holes covered in wade.scad

#40 ellensp closed 4 years ago
4
wade-big.scad nut size incorrect

#39 ellensp closed 4 years ago
3
x-end-motor/idler centres different from Z-motor mount - URGENT!

#38 droftarts opened 12 years ago
5
Flanged bearing guides can cause print issues

#37 DaleDunn closed 12 years ago
1
Made X-carriage LM8UU clamps like the X-end clamps, with pull-tie holes, etc

#36 giseburt closed 12 years ago
0
Y-Carriage parts are not listed in BOM

#35 Lodran opened 12 years ago
1
In source/metric.scad, m3_nut_diameter is far smaller than the actual diameter of an M3 nut.

#34 Lodran opened 12 years ago
2
LM8UU X-Ends are weak, and easily broken

#33 Lodran closed 12 years ago
1
X-Carriage center hole/LM8UU holder conflict

#32 Lodran opened 12 years ago
0
Wade extruder problem

#31 brad opened 12 years ago
0
Fixed x-end-motor.stl

#30 devijvers opened 12 years ago
0
Weak Z Coupling

#29 pawl closed 12 years ago
3
Integrated Z Motor Mount

#28 pawl opened 12 years ago
1
Upside Down Wades Small Gear

#27 pawl closed 12 years ago
2
Felt - adding acme leadscrew support for Z axis.

#26 redvers closed 3 years ago
0
Fix typos in the sae stuff

#25 brendanjerwin closed 12 years ago
0
refactored rod holes with pressure pad into module in teardrop.scad

#24 AxTheB closed 5 years ago
0
Edited lines 71 and 81 for correct changes from Metric to SAE.

#23 reprapperMC closed 12 years ago
0
A fix so changing pla-bushing rod size doesn't change the spaces in between the pieces.

#22 hradec closed 12 years ago
2
cleaned code a bit

#21 hintss closed 12 years ago
3