issues
search
lincomatic
/
open_evse
Firmware for Open EVSE
GNU General Public License v3.0
114
stars
161
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Size optimization
#125
toofishes
closed
3 years ago
2
Fix for compilation issues because of use of variables unneeded unless KWH_RECORDING is enabled.
#124
sorphin
closed
3 years ago
1
Detecting three phase power
#123
faustomilletari
closed
3 years ago
8
Variables undefined if KWH_RECORDING is not defined. Won't compile.
#122
sorphin
closed
3 years ago
2
RAPI command to set voltage
#121
jeremypoulter
closed
4 years ago
7
Add files via upload
#120
steepestdescent
closed
4 years ago
0
Bug Report
#119
sorphin
closed
4 years ago
1
RAPI command to set MAX current
#118
chris1howell
closed
4 years ago
7
MOSI output for Type 2 socket locking actuator
#117
DariusPL
closed
4 years ago
2
Current is only sampled while charging
#116
jeremypoulter
closed
4 years ago
1
$AT event not sent while sleeping
#115
jeremypoulter
closed
4 years ago
2
AUTH_LOCK 1 cannot be turned off by RAPI "S4 0" while in EVSE_STATE_A
#114
craigk46
closed
4 years ago
1
How to flash
#113
jbakuwel
closed
3 years ago
16
Sleeping does not indicate auth lock status
#112
beikeland
closed
4 years ago
1
Physical Security - RAPI command to disable button.
#111
chris1howell
closed
4 years ago
11
Bad temperature reading between 0oC and -0.5oC
#110
chris1howell
closed
4 years ago
4
Add files via upload
#109
steepestdescent
closed
4 years ago
2
Changes to bring Platform IO build in line with Arduino build
#108
jeremypoulter
closed
4 years ago
6
PlatformIO vs Arduino IDE: same binary firmware?
#107
jbakuwel
closed
4 years ago
14
Compiling openenergeymonitor/open_evse
#106
jbakuwel
closed
4 years ago
9
Newbie
#105
jbakuwel
closed
4 years ago
5
RAPI over I2C
#104
wecansu
closed
5 years ago
1
Should I really use Arduino 1.6
#103
Mike4U
closed
5 years ago
1
Going to sleep while charging trips GFCI
#102
Stef-Sijben
closed
4 years ago
5
In order to start support of car identification
#101
yheynema
closed
5 years ago
3
RAPI command to set voltage
#100
chris1howell
closed
4 years ago
5
State: EV Connected / Disconnected while sleeping
#99
glynhudson
closed
5 years ago
6
Is it possible to run OpenEVSE without an LCD display?
#98
DeltaVetal26
closed
5 years ago
9
PCF8574 support
#97
martiinezz
closed
5 years ago
4
Energy Limit: additive rather than cumulative
#96
glynhudson
closed
5 years ago
2
Overcurrent feature: delay required
#95
glynhudson
closed
5 years ago
16
Minimal build
#94
landswellsong
closed
5 years ago
1
Auth_Lock and EEPROM
#93
DeltaVetal26
closed
5 years ago
1
Pin change RelayAC
#92
DeltaVetal26
closed
6 years ago
5
Where can I find eeprom_24.bin?
#91
DeltaVetal26
closed
6 years ago
1
PP_AUTO_AMPACITY should set absolute maximum charge for a single session
#90
glynhudson
closed
6 years ago
7
$FS 'rebounds' when trying to pause a delay timer charge
#89
glynhudson
closed
6 years ago
1
$FE does not work when delay timer is active
#88
glynhudson
closed
6 years ago
11
Overcurrent cutout?
#87
glynhudson
closed
6 years ago
7
PP_TABLE_TESLA?
#86
glynhudson
closed
6 years ago
3
Delay end time not stopping charge
#85
glynhudson
closed
6 years ago
17
Three-phase energy calculation option
#84
glynhudson
closed
6 years ago
5
230v/400v single/three phase detection and correct energy calculations.
#83
beikeland
closed
6 years ago
2
Restore LCD display after corruption
#82
glynhudson
closed
6 years ago
5
Alert user when temperature throttling was activated during a charge session
#81
glynhudson
closed
6 years ago
15
Set temporary (single session only) charging current
#80
glynhudson
closed
6 years ago
4
Session elapsed time should be consistent with session energy
#79
glynhudson
closed
6 years ago
3
extended_fuses setting causes unreliable booting
#78
AntaresAdroit
closed
6 years ago
1
Session Wh Counter Code Not Accurate
#77
lincomatic
closed
6 years ago
1
Session Wh counter does not reset if using delay timer
#76
glynhudson
closed
6 years ago
3
Previous
Next