issues
search
makers-for-life
/
makair-firmware
🧠[Software] Firmware for the MakAir microcontroller. The brain of the ventilator.
Other
20
stars
11
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Very discretet to follow
#89
vickyknp
opened
2 years ago
0
Release v4.1.0
#88
valeriansaliou
closed
3 years ago
0
Implement EOL on telemetry
#87
valeriansaliou
closed
3 years ago
1
Move back test to previous directory
#86
valeriansaliou
closed
3 years ago
0
Refactor directory structure (normalize & de-dup & clear unused files)
#85
valeriansaliou
closed
3 years ago
0
Add pending version details
#84
valeriansaliou
closed
3 years ago
0
Fixes + send all fatal errors to telemetry on startup calibration (full tested w/ UI)
#83
valeriansaliou
closed
3 years ago
0
Add automation scripts
#82
valeriansaliou
closed
3 years ago
0
Translate End Of Line Mode
#81
baptistejamin
closed
3 years ago
0
Update STM32duino to 2.0.0
#80
dsferruzza
closed
3 years ago
1
Add pressure alarms for Volume Control
#79
baptistejamin
opened
3 years ago
0
Blower PPM progressive ramp-up when increasing speed (reduce current peaks)
#78
valeriansaliou
closed
3 years ago
3
support SFM3019 inspiratory sensor
#77
pi-r-p
closed
3 years ago
0
Remove simulation flag.
#76
jabby
closed
3 years ago
0
fix mains not detected issue
#75
pi-r-p
closed
3 years ago
0
Fix buzzer weird start
#74
pi-r-p
closed
3 years ago
0
Dev
#73
Benhalor
closed
3 years ago
1
Double mass flow meter
#72
pi-r-p
closed
3 years ago
0
Add new alarms
#71
Benhalor
opened
3 years ago
1
EOL improvement
#70
Benhalor
opened
3 years ago
0
Rpi Watchdog
#69
pi-r-p
closed
3 years ago
1
Rpi watchdog
#68
pi-r-p
closed
3 years ago
2
Add alarm snooze status to telemetry messages
#67
dsferruzza
closed
3 years ago
1
support of power supply mains connection to expander
#66
pi-r-p
closed
3 years ago
2
When calibration failed, restart calibration if START is pressed
#65
baptistejamin
closed
3 years ago
1
Mass flow meter rework
#64
pi-r-p
closed
3 years ago
0
alarm off ignored when pause/start cycle
#63
pi-r-p
opened
3 years ago
1
Extend control protocol to allow to start/stop respiration
#62
dsferruzza
closed
3 years ago
0
Drop useless support + Major refactoring
#61
Benhalor
closed
3 years ago
0
Support several respiration modes (changeable at runtime)
#60
dsferruzza
closed
3 years ago
0
Improve eol test
#59
Benhalor
closed
3 years ago
1
test the mass flow meter during the eol test
#58
Benhalor
closed
3 years ago
0
move the watchdog check, and add an explicit message for the user
#57
Benhalor
closed
3 years ago
0
Activate the snooze led
#56
Benhalor
closed
3 years ago
0
Add a WatchdogRestart telemetry message
#55
dsferruzza
closed
3 years ago
0
Watchdog is accidentally raised in some case when trigger is enabled
#54
Benhalor
closed
3 years ago
1
Remove compatibility with HW1 and HW2
#53
dsferruzza
closed
3 years ago
2
Update to STM32duino 1.9.0
#52
dsferruzza
closed
3 years ago
0
Prevent negative integral coefficient when peep > 15 cmH2O
#51
Benhalor
closed
3 years ago
1
Check the watchdog restart at the beginning
#50
Benhalor
closed
3 years ago
0
manage flowmeter reset the hardware way
#49
pi-r-p
closed
3 years ago
0
Check ms/us overflows
#48
pi-r-p
opened
3 years ago
0
"Battery low" alarm should be downgraded to a warning
#47
Benhalor
opened
3 years ago
1
Auto-test the flow meter at starting
#46
Benhalor
closed
3 years ago
1
Alarm when expiratory branch is (partially) blocked
#45
Benhalor
opened
3 years ago
2
Buzzer review
#44
Benhalor
opened
3 years ago
0
Drive the LED associated with the buzzer OFF
#43
Benhalor
closed
3 years ago
1
EOL test
#42
Benhalor
closed
3 years ago
2
fix a bug in trigger mode that raise the watchdog when stopping the m…
#41
Benhalor
closed
3 years ago
0
Convert telemetry acknowledge pressures in cmh2O
#40
Benhalor
closed
3 years ago
2
Next