issues
search
matsstaff
/
stc1000p
Programmable thermostat firmware and arduino based uploader for the STC-1000 thermostat
GNU General Public License v3.0
260
stars
47
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
STC1000 with 78F9224 / 78K0S processor supported?
#110
WolfganP
opened
2 years ago
2
Off-Grid Solar Refrigerator
#109
mbr1989
opened
2 years ago
8
Change Probe with 10K 3950
#108
tava999
opened
3 years ago
5
millisx60 should be reset when updating dh config value
#107
fredericsureau
closed
3 years ago
2
433MHz FO post-preamble gap
#106
plsecker
closed
4 years ago
1
build error
#105
sveco86
closed
5 years ago
4
Controlling STC1000p with COM over internet (by writting to EEPROM)
#104
sveco86
opened
5 years ago
3
RFXcom
#103
guan57
opened
5 years ago
0
The link to the STC-1000 on AliExpress is dead
#102
leogout
closed
5 years ago
1
E-1000 compatibility
#101
FredrikH-R
opened
6 years ago
1
support for Holtek HT66F40 (Lerway) based models
#100
dt
closed
6 years ago
2
looping
#99
Badfraggle
opened
7 years ago
4
OVBSC - Relay repeatedly ON/OFF every ~4 seconds
#98
dboyd13
closed
7 years ago
1
Selectable Output for Mash Steps
#97
kaljade
opened
7 years ago
0
S0 too powerful for ramping between mash steps
#96
karlp
closed
7 years ago
3
More information needed to wire up pump control with the dimmer on OVBSC README
#95
diablothe2nd
opened
7 years ago
1
Minute: Setpoint not updated in thermostat mode
#94
matsstaff
opened
8 years ago
0
OVBSC Separate SO (Strike Output) Variable Into Two Variables
#93
flynut
opened
8 years ago
1
OVBSC Whirlpool Step
#92
flynut
opened
8 years ago
2
OVBSC cooling step?
#91
matsstaff
opened
8 years ago
0
OVBSC: not entering thermostat mode when strike temperature reached
#90
karlp
closed
7 years ago
7
Negative temperatures in 433MHz
#89
matsstaff
opened
8 years ago
0
Fix com example sketch
#88
matsstaff
closed
8 years ago
0
optimize handle_com by refactoring state and 16/8 bit data
#87
seanmcveigh
closed
8 years ago
2
Improve 'button up' information in OVBSC
#86
matsstaff
opened
8 years ago
2
STC-1000+ Brew
#85
ep98juma
closed
8 years ago
1
optimize button handling code by using bit operations
#84
seanmcveigh
closed
8 years ago
1
Com example sketch has broken menu handling
#83
matsstaff
closed
8 years ago
1
shave 8 instructions out of read_ad
#82
seanmcveigh
closed
8 years ago
1
Optimization
#81
seanmcveigh
closed
8 years ago
1
use bitwise operators to distinguish different decimal/degrees modes
#80
seanmcveigh
closed
8 years ago
2
optimize the temperare LUT interpolation
#79
seanmcveigh
closed
8 years ago
1
optimize multiplication by 10 further
#78
seanmcveigh
closed
8 years ago
0
optimize range checking of adfilter value in ad_to_temp()
#77
seanmcveigh
closed
8 years ago
0
Merge master
#76
matsstaff
closed
8 years ago
0
optimized ADC range checking code and probe2 check. saves 142 bytes.
#75
seanmcveigh
closed
8 years ago
2
Conditional inclusion C/F HEX data in sketch.
#74
matsstaff
closed
8 years ago
1
second temperature probe inquiry
#73
seanmcveigh
closed
8 years ago
9
Compilation fails on newer versions of Arduino IDE
#72
matsstaff
closed
8 years ago
1
use Spark core
#71
bateau84
closed
8 years ago
1
Get Device ID error message
#70
CNevay
closed
8 years ago
2
Dual Probe_Minute program
#69
capt9859
closed
8 years ago
1
New A400-p PCB from ALiExpress "U-Control"
#68
hidara2000
closed
8 years ago
10
Buttons reversed
#67
hebs
closed
8 years ago
2
Fix profile generator.
#66
batnas
closed
8 years ago
1
Added humidity control firmware
#65
matsstaff
closed
8 years ago
0
Merge
#64
matsstaff
closed
8 years ago
0
STC1000 version using N96A8211 conversion to PIC 16F1828 is possible.
#63
anil001
closed
8 years ago
1
User defined temperature display
#62
kaljade
closed
8 years ago
1
Make SP first menu item
#61
matsstaff
closed
8 years ago
1
Next