milaq rpi-rf issues - Githubissues

milaq / rpi-rf

Sending and receiving 433MHz signals with cheap GPIO RF modules on a Raspberry Pi

BSD 3-Clause "New" or "Revised" License

504 stars 179 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Any chance to work with gpiozero?

#73 tkhkbn opened 11 months ago
7
length of sending data issue

#72 KaiyuHu opened 1 year ago
1
Add GPIO.mode BOARD for usage with BOARD pin numbering

#71 hasenradball opened 1 year ago
0
[Question]: Set GPIO.mode Via RFDevice Constructor

#70 hasenradball opened 1 year ago
0
Not receiving codes from remote buttons

#69 okaapi opened 1 year ago
0
Doesn't wprk if I put receiver' code into py file

#68 ilyamordasov opened 1 year ago
0
[Question Regarding switcing Sockets]: Brennenstuhl RCS 1000N

#67 hasenradball closed 1 year ago
3
Not receiving signal with receivers (SRX882 or other one)

#66 IpPsar01 opened 2 years ago
1
Conversion for Raspberry Pi Pico

#65 pbillerot opened 2 years ago
1
Receiving a bit too much?

#64 lee-van-oetz opened 2 years ago
1
Possible to recieve sent signals from same raspberry pi?

#63 Currently-Dead opened 2 years ago
1
Fix tx_length when using nexa protocol

#62 brnomendes closed 2 years ago
0
Cleanup cleans up all pins

#61 paf0186 opened 2 years ago
1
Rpi-rf not working on Pi Zero W

#60 juergen2345 opened 2 years ago
2
Projector screen

#59 La7dan opened 3 years ago
0
Python 2.7 compatibility fix

#58 puetro opened 3 years ago
0
RPI 4 installation not working

#57 myroom opened 3 years ago
1
rpi_rf not receiving data correctly from a supported remote, can not get codes... this is causing Mycodo not to work.

#56 LucidEye closed 3 years ago
0
Long key press help / advice

#55 Electrik-rich546456 opened 3 years ago
1
Need your help/advice

#54 Electrik-rich546456 opened 3 years ago
0
recieved sygnal logging

#53 Ghvinerias opened 3 years ago
0
How to add new protocol without modify source code?

#52 GF-Huang opened 3 years ago
0
How could I transmit my received data using rpitx?

#51 developerfromjokela opened 4 years ago
0
Decoder to extract RF codes

#50 Swiftwork opened 4 years ago
0
Update README.rst

#49 timmillwood opened 4 years ago
0
send.py disables other remote controls

#48 Al- opened 4 years ago
2
Reading results not interpretable and always different

#47 andreaj8 opened 4 years ago
9
How do I install this on Hassio ??

#46 richardhughes260 opened 4 years ago
0
Code not repeating but periodic

#45 jonasstoetzel opened 4 years ago
0
Something really wrong with send script?

#44 dachshund-digital opened 5 years ago
0
RPI 3B+

#43 zen0fall closed 5 years ago
1
Help with protocol difference

#42 sekisek opened 5 years ago
1
Providing Code to Parameter

#41 basimms closed 5 years ago
1
RPI 3B installation not working

#40 ModischFabrications opened 5 years ago
1
Added support for inverted waveforms and 2 extra protocols

#39 toSvenson opened 5 years ago
0
Improve receiving quality

#38 turbulator closed 5 years ago
2
does rpi-rf support 434mhz transmitter/receiver?

#37 Rihcus closed 5 years ago
0
Why no voltage divider on wiring diagram?

#36 bulletmark closed 5 years ago
1
Command-line arguments for specifying protocol parameters

#35 rgov opened 6 years ago
0
Error in the code?

#34 AzaPattaz closed 6 years ago
2
send error

#33 hacktorious closed 6 years ago
6
receive codes seem incorrect

#32 hacktorious opened 6 years ago
0
function's arguments mismatch

#31 yossigartner closed 5 years ago
5
[Errno 11] write could not complete without blocking

#30 chathurangawijetunge opened 6 years ago
1
Need your help/advice

#29 metabsd closed 4 years ago
2
Rd buffer clean up

#28 chathurangawijetunge closed 6 years ago
0
Misleading var names and log messages GPIO mode

#27 AsharLohmar opened 6 years ago
2
Can't start at boot up

#26 chathurangawijetunge closed 6 years ago
0
Add bitlength parameter

#25 giuseppeg88 closed 6 years ago
6
Long range advice

#24 sekisek closed 6 years ago
3