Open olli991 opened 2 years ago
mib.zip MST2_EU_VW_ZR_P0125T
Added https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
Fixed https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
You need 4 ingredients to make it work:
Good luck!
swdl patch worked not for me...
try to install new sw
parse error metainfo checksum key already exists
There're no clairvoyants here, please attach your dump :)
mib.zip MST2_EU_VW_ZR_P0125T
Added https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
Fixed https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
You need 4 ingredients to make it work:
- USB port 5Q0035726E. Check USB port type in Toolbox>mib_info
- Set bits 6-7 of byte 19 of coding of 5F to 11
- Enable adaptations in 5F: ENG109862-ENG130249-Vehicle_configuration-Apple_DIO,active ENG109862-ENG130248-Vehicle_configuration-Google_GAL,active
- Proper cable like https://cutt.ly/jgrI1Vf
Good luck!
... you forgot the most important point no. 5, which is the new unit from sw minimun 02.. on the current sw. 01.. only Mirrorlink is possible :)
@Osnarom
As yox2019 is absolutely right about fw 1xx. Long press MENU and take a look at the "Supported FEC" list. Which codes do you see there? Just list/type the numbers here, we trust you without photo :)
Hi Iprot Today I,m try again update my unit, but I have also this same problem like befor I,m change metainfo like You scribe before "change all \22\ to \18\
metainfo and also dump files are send You again Please look at this SEZAZ2R0139869.zip
Hi Iprot Today I,m try again update my unit, but I have also this same problem like befor I,m change metainfo like You scribe before "change all \22\ to \18\
metainfo and also dump files are send You again Please look at this SEZAZ2R0139869.zip
Which error exactly do you see now?
Can't use update container.The current software download application is too old
Can't use update container.The current software download application is too old
Ah, sure, forgot to mention that you also need to Ctrl+H RequiredVersionOfDM = "3349000" to RequiredVersionOfDM = "0" Then it will work ;)
MST2_EU_SE_ZR_P0479T.zip h24 0479 sofware android carplay does not work
MST2_EU_SE_ZR_P0479T.zip h24 0479 sofware android carplay does not work
Already supported. Scroll up, read carefully and check if all ingredients are setup properly.
thx. it realy does work.
MST2_EU_SK_ZR_P0369T.zip This is a Composition Media, can't patch SWAP and CP.
Added https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
Added https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip To add CP support you need to provide CP folder.
MST2_US_VW_PQ_P0254T.zip can't patch cp hmi.zip
still getting the same error
still getting the same error
https://github.com/olli991/mib-std2-pq-zr-toolbox/commit/76611eb8f2333a6cd8a11cefcc14e74f92433dd9
hi or downloaded the firmware for seat ateca, MST2_EU_SE_ZR_P0479T.7z when he starts to install it he tells me, it was not possible to read the meta info file, why? thanks help
Hi , today I tried to "Patch tsd.mibstd2.system.swap and generate EL" The script has finished. He prompted me to restart the unit. Mirrorlink did not work after reboot. There was no entry in the installed codes section (Fec / SWaP). No new code via OBDeleven could be added to the unit.
Thanks in advance
If you see, mirror link without asking for activation key, so everything is ok, the main problems is that smartphone no longer support mirror link,
There is any update for this firmware and unit who will let me activate android auto ?
Not for p01xx
hello me or this software MST2_EU_SE_ZR_P0359T, what software can I install? Thank you
hello me or this software MST2_EU_SE_ZR_P0359T, what software can I install? Thank you
hello me or this software MST2_EU_SE_ZR_P0359T, what software can I install? Thank you
2023-04-12 20:25 GMT+02:00, Medmimoza @.***>:
Not for p01xx
-- Reply to this email directly or view it on GitHub: https://github.com/olli991/mib-std2-pq-zr-toolbox/issues/93#issuecomment-1505735280 You are receiving this because you commented.
Message ID: @.***>
Still I have some concern about my unit , bought it from ebay , no idea who code it , I will attach some pictures
as seen from images my unit had an update to MST2_EU_VW_PQ_P0367T and after had another update to the recent firmware could be possible the unit to be a PQ and not ZR unit ?
My unit was first with a GEM of 3.X, and I didn't overwrite the CPU files, which as a result it didn't work for the first time. I later installed the correct one and patched the unit, however in 5F Multimedia there's still fault for CP active. I re-entered GEM and found out somehow my GEM version was upgraded to 4.1.1, so I uninstalled the toolbox and reinstalled the version for non SW 01XX/02XX+GEM3.X, and patched again, which still has the fault for CP active. The unit itself was still usable, but it whenever I enter GEM and get out, the "component protection is active" message pops out again, and I have to re-patch it. I still believe the unit hasn't been patched. dump.zip
CP off patch don`t work (unknown file size)
File size 2197503 not detected for CP patch.
Thank you so much !
Added in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
CP off patch don`t work (unknown file size)
Added in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
My unit was first with a GEM of 3.X, and I didn't overwrite the CPU files, which as a result it didn't work for the first time. I later installed the correct one and patched the unit, however in 5F Multimedia there's still fault for CP active. I re-entered GEM and found out somehow my GEM version was upgraded to 4.1.1, so I uninstalled the toolbox and reinstalled the version for non SW 01XX/02XX+GEM3.X, and patched again, which still has the fault for CP active. The unit itself was still usable, but it whenever I enter GEM and get out, the "component protection is active" message pops out again, and I have to re-patch it. I still believe the unit hasn't been patched. dump.zip
@lprot Hi! Would you mind take a look at my dump file? I still didn't manage to make it work and the CP pops back. Thanks a lot!
My unit was first with a GEM of 3.X, and I didn't overwrite the CPU files, which as a result it didn't work for the first time. I later installed the correct one and patched the unit, however in 5F Multimedia there's still fault for CP active. I re-entered GEM and found out somehow my GEM version was upgraded to 4.1.1, so I uninstalled the toolbox and reinstalled the version for non SW 01XX/02XX+GEM3.X, and patched again, which still has the fault for CP active. The unit itself was still usable, but it whenever I enter GEM and get out, the "component protection is active" message pops out again, and I have to re-patch it. I still believe the unit hasn't been patched. dump.zip
@lprot Hi! Would you mind take a look at my dump file? I still didn't manage to make it work and the CP pops back. Thanks a lot!
Already supported in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip Update to fw 254 install toolbox again and run the patch.
Thank you for your reply
No patch SWAP for EU ZR 245 ? MST2_EU_SE_ZR_P0245T.zip
No patch SWAP for EU ZR 245 ? MST2_EU_SE_ZR_P0245T.zip
Already added in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
My unit was first with a GEM of 3.X, and I didn't overwrite the CPU files, which as a result it didn't work for the first time. I later installed the correct one and patched the unit, however in 5F Multimedia there's still fault for CP active. I re-entered GEM and found out somehow my GEM version was upgraded to 4.1.1, so I uninstalled the toolbox and reinstalled the version for non SW 01XX/02XX+GEM3.X, and patched again, which still has the fault for CP active. The unit itself was still usable, but it whenever I enter GEM and get out, the "component protection is active" message pops out again, and I have to re-patch it. I still believe the unit hasn't been patched. dump.zip
@lprot Hi! Would you mind take a look at my dump file? I still didn't manage to make it work and the CP pops back. Thanks a lot!
Already supported in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip Update to fw 254 install toolbox again and run the patch.
Hi, I just updated to the latest official firmware for this machine, 0253T. I cannot find 0254. However the patch is still not working. Do I have to get a firmware 0254? MST2_US_VW_PQ_P0253T.zip
Hi, I just updated to the latest official firmware for this machine, 0253T. I cannot find 0254. However the patch is still not working. Do I have to get a firmware 0254? MST2_US_VW_PQ_P0253T.zip
Already supported in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
Hi, I just updated to the latest official firmware for this machine, 0253T. I cannot find 0254. However the patch is still not working. Do I have to get a firmware 0254? MST2_US_VW_PQ_P0253T.zip
Already supported in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
Somehow after running the CP Patch script and reboot, it still says CP active. Have the dump files in the zip document above. Please take a look, thank you !!
can you please check the below support.zip
can you please check the below support.zip
Already supported in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
can you please check the below support.zip
Already supported in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
Thanks for quick response, i have tried it but still giving me unknown file size 1 detected
am i missing some step can you please advise.
can you please check the below support.zip
Already supported in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
Thanks for quick response, i have tried it but still giving me unknown file size 1 detected
am i missing some step can you please advise.
Hi, is there any update for units with 1 sd and sw0138 to do the cp off without getting in the bootloop
Hi, is there any update for units with 1 sd and sw0138 to do the cp off without getting in the bootloop
no
Hi, today I wanted to apply the patch "Patch tsd.mibstd2.system.swdownload to accept any metainfo.txt" "Unknown file size 3063420 detected" messa изображение_viber_2023-06-06_21-11-13-714 ge appeared I'm attaching a support folder. support.zip
Will it be possible to use this feature in the future? Thank you
Hi, today I wanted to apply the patch "Patch tsd.mibstd2.system.swdownload to accept any metainfo.txt" "Unknown file size 3063420 detected" messa изображение_viber_2023-06-06_21-11-13-714 ge appeared I'm attaching a support folder. support.zip
Will it be possible to use this feature in the future? Thank you
Added to https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip Update and patch again.
Hi, today I wanted to apply the patch "Patch tsd.mibstd2.system.swdownload to accept any metainfo.txt" "Unknown file size 3084676 detected" I'm attaching a support folder.
Will it be possible to use this feature in the future?
Thank you support.zip
Hi, today I wanted to apply the patch "Patch tsd.mibstd2.system.swdownload to accept any metainfo.txt" "Unknown file size 3084676 detected" I'm attaching a support folder.
Will it be possible to use this feature in the future?
Thank you support.zip
Added in https://github.com/olli991/mib-std2-pq-zr-toolbox/archive/refs/heads/master.zip
Hi, today I wanted to apply the patch "Patch tsd.mibstd2.system.swdownload to accept any metainfo.txt" "Unknown file size 3084636 detected" I'm attaching a support folder. MST2_EU_VW_PQ_P0240T.zip
Please place your support dumps in this issue.
This applies to:
How to make a support dump?
You can find it in the "Tools" screen below the patch scripts. You'll find the filedump in the new .../support folder in the dump section of the SD card. Please zip the whole "support" folder and upload it to this thread.