rfetick MPU6050_light issues

rfetick / MPU6050_light

Lightweight, fast and simple library to communicate with the MPU6050

MIT License

123 stars 36 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

The relationship between the offsets of the standard MPU6050 class from i2cdev and this library.

#46 IlyaFedorov115 opened 1 month ago
0
Library support for MPU9250?

#45 chefseg opened 3 months ago
1
add reset functions for the angles

#44 alibustami opened 4 months ago
0
Example plotting

#43 JAndersM opened 7 months ago
0
Interrupt capabilities

#41 BenEspinoza10 opened 1 year ago
0
Angle Z drifting

#40 ImVictorYT opened 1 year ago
1
question regarding the source code and the documentation

#39 Umme3 opened 1 year ago
0
Sensor in vertical position: would like to start the angle reading (0,0,0)

#38 Umme3 opened 1 year ago
0
Wrap Z angle

#37 Kikkiu17 opened 1 year ago
3
Angles problem

#36 Marekoooo closed 1 year ago
0
how to reset all for a status = writeData(MPU6050_PWR_MGMT_1_REGISTER, 0x01) = 0 again

#35 philippedc opened 1 year ago
0
Angle Z gyro drifting

#34 Gabriel110302 opened 1 year ago
3
reset angle values to zero in void loop

#33 sandy9159 opened 1 year ago
0
Using 2 MPU6050

#32 Gugarauj07 opened 1 year ago
1
Trouble using 2 mpu

#31 JSlain opened 1 year ago
1
5 MPU6050s

#30 eiffelblithe opened 2 years ago
1
Pitch value changes with change in GyroZ

#29 frozenmafia opened 2 years ago
2
Yaw angles are constantly drifting or increasing/decreasing rapidly

#28 Jawad-RoboLearn opened 2 years ago
2
Fustion with magnetometer

#27 batata004 closed 2 years ago
1
calcOffsets not working if being called outside of setup?

#26 motedon closed 2 years ago
3
GetAngle works fine alone but "hangs" up when embedded in other sketch

#24 drbrodie opened 2 years ago
2
Suggest replacing use of math functions with float versions instead of double versions

#23 DeonMarais64 opened 2 years ago
1
Issue with ESP32

#22 shynzo opened 2 years ago
0
Without Decimal place ?!

#21 Ace-li-k closed 2 years ago
1
support of 2 sensors

#20 76nic opened 2 years ago
6
Two MPUs

#19 Maco-coder closed 2 years ago
5
'long' should be 'unsigned long' for millis value.

#18 Koepel opened 2 years ago
0
trying to use a MPU6050 and a Sabertooth2x12 on a single arduino

#17 jaekim24 closed 2 years ago
1
mpu6050 status

#16 zfranco55 closed 2 years ago
1
physical position x, y and z axes

#15 zfranco55 closed 2 years ago
1
Zeroing sensor values

#14 ivanbo97 closed 3 years ago
4
Added new register switching function to allow for multiple sensors.

#13 ghost closed 2 years ago
1
How to switch the readable register?

#12 ghost closed 2 years ago
3
What do the different status messages mean?

#11 1HighDuke closed 3 years ago
1
What is the different between inner filter and kalman filter?

#10 leaf918 closed 3 years ago
0
Pronblem with initial angular tilt.

#9 sofiane1010 closed 3 years ago
0
Where can i find and change the pin connection

#8 LedHat closed 3 years ago
4
Absolute orientation

#7 b0x4it closed 3 years ago
9
Unexpected X, Y value range when run upside down

#6 daara-s closed 3 years ago
3
M5Stack Core Esp32

#5 cacb-wg closed 3 years ago
1
Glitch on X angle value when flipping from 180 to -180

#4 Mael19 closed 3 years ago
3
Accelerometer Z Axis offset calibration

#3 audiocrush closed 3 years ago
3
ESP32 support?

#2 tonyvr4 closed 3 years ago
1
Different gyro value at startup and after reset

#1 Titibo26 opened 3 years ago
16