epevermodbus

This package is intended to help you communicate with an EPever charge controller. It has been tested with an EPever Tracer AN but should work with other EPever devices.

Features

Read real time data
Read battery parameters
Write battery parameters this feature is a work in progress
Automatic retries

Connecting to the charge controller

I have only tested this package on Linux / Raspberry Pi but I see no reason why it should not work on other devices.

For the cable you have two options

Official EPever cable

When using the offical cable on Linux your device will show up something like /dev/ttyXRUSB0. You will need to use a custom driver to use this cable on Linux rather than the bundled cdc-acm driver. It can be difficult to get this driver working properly on Linux and Raspberry Pi.

On Windows you can use the driver provided by EPever and the cable should work fine so long as you check the rs485 checkbox in device manager.

Your own custom cable

You can quite easily make your own cable if you purchase a few parts, and with this approach you won't need a custom driver on Linux so it should be easier to get working. The device should show up as something like /dev/ttyUSB0.

For more information read: https://ross-warren.co.uk/2021/08/14/building-a-cable-to-connect-my-epever-charge-controller/

Installing the package

To install the package run

pip install epevermodbus

This package requires Python 3, depending on your setup you might have to instead run:

pip3 install epevermodbus

Command line utility

To run the command line utility and see the debug output run the following on the command line:

epevermodbus --portname /dev/ttyUSB0 --slaveaddress 1

usage: epevermodbus [-h] [--portname PORTNAME] [--slaveaddress SLAVEADDRESS]

optional arguments:
  -h, --help            show this help message and exit
  --portname PORTNAME   Port name for example /dev/ttyUSB0
  --slaveaddress SLAVEADDRESS
                        Slave address 1-247
  --baudrate BAUDRATE   Baudrate to communicate with controller (default is 115200)

Example output

Real Time Data
Solar voltage: 0.02V
Solar current: 0.0A
Solar power: 0.0W
Solar power L: 0.0W
Solar power H: 0.0W
Load voltage: 0.0V
Load current: 0.0A
Load power: 0.0W
Load power L: 0.0W
Load power H: 0.0W
Battery current L: 0.0A
Battery current H: 0.0A
Battery voltage: 13.25V
Battery state of charge: 86%
Battery temperature: 16.91°C
Remote battery temperature: 0.0°C
Controller temperature: 16.55°C
Battery status: {'wrong_identifaction_for_rated_voltage': False, 'battery_inner_resistence_abnormal': False, 'temperature_warning_status': 'NORMAL', 'battery_status': 'NORMAL'}
Charging equipment status: {'input_voltage_status': 'NORMAL', 'charging_mosfet_is_short_circuit': False, 'charging_or_anti_reverse_mosfet_is_open_circuit': False, 'anti_reverse_mosfet_is_short_circuit': False, 'input_over_current': False, 'load_over_current': False, 'load_short_circuit': False, 'load_mosfet_short_circuit': False, 'disequilibrium_in_three_circuits': False, 'pv_input_short_circuit': False, 'charging_status': 'NO_CHARGING', 'fault': False, 'running': True}
Discharging equipment status: {'input_voltage_status': 'NORMAL', 'output_power_load': 'LIGHT', 'short_circuit': False, 'unable_to_discharge': False, 'unable_to_stop_discharging': False, 'output_voltage_abnormal': False, 'input_over_voltage': False, 'short_circuit_in_high_voltage_side': False, 'boost_over_voltage': False, 'output_over_voltage': False, 'fault': False, 'running': False}
Day time: False
Night time: True
Maximum battery voltage today: 14.5V
Minimum battery voltage today: 13.25V
Device over temperature: False

Battery Parameters:
Rated charging current: 20.0A
Rated load current: 20.0A
Battery real rated voltage: 12.0V
Battery type: USER_DEFINED
Battery capacity: 40AH
Temperature compensation coefficient: 0
Over voltage disconnect voltage: 14.7V
Charging limit voltage: 14.4V
Over voltage reconnect voltage: 14.6V
Equalize charging voltage: 14.4V
Boost charging voltage: 14.4V
Float charging voltage: 13.6V
Boost reconnect charging voltage: 13.3V
Low voltage reconnect voltage: 12.0V
Under voltage recover voltage: 12.0V
Under voltage warning voltage: 11.5V
Low voltage disconnect voltage: 11.0V
Discharging limit voltage: 11.0V
Battery rated voltage: 12V
Default load on/off in manual mode: OFF
Equalize duration: 0 min
Boost duration: 180 min
Battery discharge: 30%
Battery charge: 100%
Charging mode: VOLTAGE_COMPENSATION

Python usage

To use the library within your Python code

from epevermodbus.driver import EpeverChargeController

controller = EpeverChargeController("/dev/ttyUSB0", 1)

controller.get_solar_voltage()

See https://github.com/rosswarren/epevermodbus/blob/main/epevermodbus/driver.py for all available methods

rosswarren / epevermodbus

readme