This repository is in no way approved by or affiliated with the official Victron Energy repository.
I am not responsible for any problems or damages with your devices or this code
This ESPHome component supports both official Victron Bluetooth BLE Protocols:
victron_ble
.
bms_flags
and error
.output_state
.error
, io_status
and warnings_alarms
.ve_bus_error
.bmv_monitor_mode
.victron_ble_connect
.
victron_ble
component (Recommended)To connect to your Victron device you must have two information for each device:
mac_address
- Bluetooth mac address of device.bindkey
- AES encryption key.Use VictronConnect App v5.93 (or later) released on 2023-08-25.
Instant readout via Bluetooth
is enabled.SHOW
for Instant readout details Encryption data.When connected to the device via VictronConnect App no Instant readout (Bluetooth advertising) data is generated.
victron_ble
using SmartShunt and SmartSolarSee victron_ble.yaml for a full example.
esphome:
name: "victron-ble"
external_components:
- source: github://Fabian-Schmidt/esphome-victron_ble
esp32:
board: esp32dev
logger:
level: DEBUG
esp32_ble_tracker:
victron_ble:
- id: MySmartShunt
mac_address: "MY SMART SHUNT MAC"
bindkey: "MY AES ENCRYPTION KEY"
- id: MySmartSolar
mac_address: "MY SMART SOLAR MAC"
bindkey: "MY AES ENCRYPTION KEY"
sensor:
# MySmartShunt
- platform: victron_ble
victron_ble_id: MySmartShunt
name: "Time remaining"
type: TIME_TO_GO
- platform: victron_ble
victron_ble_id: MySmartShunt
name: "Battery voltage"
type: BATTERY_VOLTAGE
- platform: victron_ble
victron_ble_id: MySmartShunt
name: "Starter Battery"
# AUX_VOLTAGE or MID_VOLTAGE or TEMPERATURE.
# Depending on configuration of SmartShunt.
type: AUX_VOLTAGE
- platform: victron_ble
victron_ble_id: MySmartShunt
name: "Current"
type: BATTERY_CURRENT
- platform: victron_ble
victron_ble_id: MySmartShunt
name: "Consumed Ah"
type: CONSUMED_AH
- platform: victron_ble
victron_ble_id: MySmartShunt
name: "State of charge"
type: STATE_OF_CHARGE
# MySmartSolar
- platform: victron_ble
victron_ble_id: MySmartSolar
name: "Battery Voltage"
type: BATTERY_VOLTAGE
- platform: victron_ble
victron_ble_id: MySmartSolar
name: "Battery Current"
type: BATTERY_CURRENT
- platform: victron_ble
victron_ble_id: MySmartSolar
name: "Yield Today"
type: YIELD_TODAY
- platform: victron_ble
victron_ble_id: MySmartSolar
name: "PV Power"
type: PV_POWER
- platform: victron_ble
victron_ble_id: MySmartSolar
name: "Load Current"
type: LOAD_CURRENT
binary_sensor:
- platform: victron_ble
victron_ble_id: MySmartShunt
name: "Battery has Alarm"
type: ALARM
- platform: victron_ble
victron_ble_id: MySmartSolar
name: "MPPT is in Fault state"
type: DEVICE_STATE_FAULT
- platform: victron_ble
victron_ble_id: MySmartSolar
name: "MPPT has Error"
type: CHARGER_ERROR
text_sensor:
- platform: victron_ble
victron_ble_id: MySmartShunt
name: "Battery Alarm reason"
type: ALARM_REASON
- platform: victron_ble
victron_ble_id: MySmartSolar
name: "MPPT state"
type: DEVICE_STATE
- platform: victron_ble
victron_ble_id: MySmartSolar
name: "MPPT Error reason"
type: CHARGER_ERROR
victron_ble
component configurationThe following settings exist:
mac_address
- The MAC address of your Victron device.bindkey
- The AES encryption key of your Victron device.on_message
- When any message is recieved.on_battery_monitor_message
- When a battery monitor message is recieved.on_solar_charger_message
- When a solar charger message is recieved.on_inverter_message
- When a inverter message is recieved.on_dcdc_converter_message
- When a DC/DC converter message is recieved.on_smart_lithium_message
- When a smart Lithium message is recieved.on_inverter_rs_message
- When a Inverter RS message is recieved.on_smart_battery_protect_message
- When a Smart Battery Protect message is recieved.on_lynx_smart_bms_message
- When a Lynx (Smart BMS) message is recieved.on_multi_rs_message
- When a Multi RS message is recieved.on_ve_bus_message
- When a VE.Bus message is recieved.on_dc_energy_meter_message
- When a DC Energy meter message is recieved.on_orion_xs_message
- When a Orion XS message is recieved.The following type
are supported by the sensor
component:
Unit | Solar charger | Battery monitor | Inverter | DC/DC converter | SmartLithium | Inverter RS | Smart Battery Protect | (Lynx Smart) BMS | Multi RS | VE.Bus | DC Energy Meter | Orion XS | |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ACTIVE_AC_IN |
X | X | |||||||||||
ACTIVE_AC_IN_POWER |
W | X | X | ||||||||||
AC_APPARENT_POWER |
VA | X | |||||||||||
AC_CURRENT |
A | X | |||||||||||
AC_OUT_POWER |
W | X | X | X | |||||||||
AC_VOLTAGE |
V | X | |||||||||||
ALARM_REASON |
X | X | X | X | |||||||||
AUX_VOLTAGE |
V | X(1) | X(1) | ||||||||||
BATTERY_CURRENT |
A | X | X | X | X | X | X | X | |||||
BATTERY_VOLTAGE |
V | X | X | X | X | X | X | X | X | X | |||
BATTERY_POWER |
W | X | X | X | X | X | X | X | |||||
CHARGER_ERROR |
X | X | X | X | X | ||||||||
CONSUMED_AH |
Ah | X | X | ||||||||||
DEVICE_STATE |
X | X | X | X | X | X | X | X | |||||
ERROR |
X | X | X | X | |||||||||
INPUT_VOLTAGE |
V | X | X | X | |||||||||
LOAD_CURRENT |
A | X | |||||||||||
OFF_REASON |
X | X | X | ||||||||||
OUTPUT_VOLTAGE |
V | X | X | X | |||||||||
MID_VOLTAGE |
V | X(1) | |||||||||||
PV_POWER |
W | X | X | X | |||||||||
STATE_OF_CHARGE |
% | X | X | X | |||||||||
TEMPERATURE |
°C | X(1) | X | X(2) | X | X(1) | |||||||
TIME_TO_GO |
min | X | X | ||||||||||
YIELD_TODAY |
kWh | X | X | X | |||||||||
BALANCER_STATUS |
X | ||||||||||||
BMS_FLAGS |
X | ||||||||||||
CELL1 |
V | X | |||||||||||
CELL2 |
V | X | |||||||||||
CELL3 |
V | X | |||||||||||
CELL4 |
V | X | |||||||||||
CELL5 |
V | X | |||||||||||
CELL6 |
V | X | |||||||||||
CELL7 |
V | X | |||||||||||
CELL8 |
V | X | |||||||||||
OUTPUT_STATE |
X | ||||||||||||
WARNING_REASON |
X | ||||||||||||
IO_STATUS |
X | ||||||||||||
WARNINGS_ALARMS |
X | ||||||||||||
ALARM |
X | ||||||||||||
BMV_MONITOR_MODE |
X | ||||||||||||
OUTPUT_CURRENT |
X | ||||||||||||
INPUT_CURRENT |
X |
(1) - Available if device aux port is configured.
(2) - Not available on all models. NAN
reported if not available.
The following type
are supported by the binary_sensor
component:
Solar charger | Battery monitor | Inverter | DC/DC converter | SmartLithium | Inverter RS | Smart Battery Protect | (Lynx Smart) BMS | Multi RS | VE.Bus | DC Energy Meter | Orion XS | |
---|---|---|---|---|---|---|---|---|---|---|---|---|
ALARM |
X | X | X | X | ||||||||
CHARGER_ERROR |
X | X | X | X | X | |||||||
DEVICE_STATE_OFF |
X | X | X | X | X | X | X | X | ||||
DEVICE_STATE_LOW_POWER |
? | ? | ? | |||||||||
DEVICE_STATE_FAULT |
X | X | X | X | X | X | X | X | ||||
DEVICE_STATE_BULK |
X | ? | ? | ? | X | |||||||
DEVICE_STATE_ABSORPTION |
X | ? | ? | ? | X | |||||||
DEVICE_STATE_FLOAT |
X | ? | ? | ? | X | |||||||
DEVICE_STATE_STORAGE |
? | ? | ? | |||||||||
DEVICE_STATE_EQUALIZE_MANUAL |
X | ? | ? | ? | ||||||||
DEVICE_STATE_INVERTING |
? | ? | ? | |||||||||
DEVICE_STATE_POWER_SUPPLY |
? | ? | ? | |||||||||
DEVICE_STATE_SUSTAIN |
? | X | ? | |||||||||
DEVICE_STATE_STARTING_UP |
X | ? | ? | ? | ||||||||
DEVICE_STATE_REPEATED_ABSORPTION |
? | ? | ? | |||||||||
DEVICE_STATE_AUTO_EQUALIZE |
X | ? | ? | ? | ||||||||
DEVICE_STATE_BATTERY_SAFE |
? | ? | ? | |||||||||
DEVICE_STATE_EXTERNAL_CONTROL |
X | ? | ? | ? |
? - Device submits a device state. Not sure if it can enter this stage.
The following type
are supported by the text_sensor
component:
Solar charger | Battery monitor | Inverter | DC/DC converter | SmartLithium | Inverter RS | Smart Battery Protect | (Lynx Smart) BMS | Multi RS | VE.Bus | DC Energy Meter | Orion XS | |
---|---|---|---|---|---|---|---|---|---|---|---|---|
ACTIVE_AC_IN |
X | X | ||||||||||
ALARM_REASON |
X | X | X | X | ||||||||
CHARGER_ERROR |
X | X | X | X | X | |||||||
DEVICE_STATE |
X | X | X | X | X | X | X | X | ||||
OFF_REASON |
X | X | X | |||||||||
ERROR_CODE |
X | |||||||||||
WARNING_REASON |
X | |||||||||||
ALARM |
X | |||||||||||
BALANCER_STATUS |
X |
victron_ble_connect
componentvictron_scanner
to find mac address of your SmartShunt.Use the Victron scanner component to find the MAC address of your Victron Smart Shunt.
esphome:
name: "victron-scanner"
external_components:
- source: github://Fabian-Schmidt/esphome-victron_ble
esp32:
board: esp32dev
logger:
level: INFO
esp32_ble_tracker:
victron_scanner:
Check the console of ESP Home to find the message like this:
[I][victron_scanner:044]: FOUND SMART SHUNT 500A/50mV 'My SmartShunt' at AB:CD:EF:01:02:03
victron_ble_connect
esphome:
name: "victron-ble"
external_components:
- source: github://Fabian-Schmidt/esphome-victron_ble
esp32_ble:
io_capability: keyboard_only
ble_client:
- mac_address: <MY VICTRON SMART SHUNT MAC ADDRESS>
id: victron_smart_shunt_ble_client_id
on_passkey_request:
then:
- ble_client.passkey_reply:
id: victron_smart_shunt_ble_client_id
passkey: !secret ble_passkey
sensor:
- platform: victron_ble_connect
ble_client_id: victron_smart_shunt_ble_client_id
state_of_charge:
name: "State of Charge"
voltage:
name: "Voltage"
power:
name: "Power Consumption"
current:
name: "Current"
ah:
name: "Consumed Ah"
starter_battery_voltage:
name: "Starter Battery Voltage"
remaining_time:
name: "Remaining Time"
See victron_ble_connect_all.yaml for a full example.
Assumption is you are having a secret.yaml
in the same folder.
I don't have access to all Victron devices. Please provide feedback if the component is working and all values are correct and match the reading within the Victron app. Only after I got feedback for all devices I can try to get this merged into ESP Home. Given the size of this component I don't expect this soon or be a quick process.
Missing feedback for the following devices:
bms_flags
and error
.output_state
.error
, io_status
and warnings_alarms
.ve_bus_error
.