This is an Arduino 2.4GHz radio and IR transmitter for Atmel AVR

Features:

IR transmitter for "LEGO" Powerfunctions and trains as well as for "MECCANO" motors
2.4GHz radio transmitter for RC cars, helicopters etc.
4 analog axes, 2 mode switches (joystick buttons)
1 potentiometer for adjustments like the MRSC stability control
4 push buttons for transmission mode and vehicle selection as well as menu navigation
20 seletcable vehicle addresses, so you can use it for more than one vehicle
3.3V, 8MHz Pro Mini (a Pro Micro is not supported anymore due to additional functionality)
STM32 ARM version (deprecated) see: https://github.com/TheDIYGuy999/RC_Transmitter_STM32
2.4GHz NRF24L01 radio module
Support for 0.96" I2C OLED
Configuration menu for: Channel direction reversing, servo travel adjustment (independent for each vehicle)
Configuration values are stored in EEPROM
NRF24L01+PA+LNA SMA radio modules with power amplifier are supported from board version 1.1
very compact
Eagle PCB included
PONG Game included

New in V 1.3:

Infrared codes for "MECCANO" IR controlled motors. Separate library required: https://github.com/TheDIYGuy999/MeccanoIr
Multichannel transmission

New in V 1.4:

10 vehicle addresses instead of 5
The "BACK" button can now be used (if the menu screen is not displayed on the OLED) as a momentary button, for example for a horn on the vehicle. It is sent as "data.momentary1"
The "A6" potentiometer connector is now integrated in the code and is sent to the vehicle as "data.pot1"
SimpleTimer library replaced with my own code, which uses significantly less memory
EEPROM reset function added: press "Select" and "Back" during power on

New in V 1.41:

New in V 1.42:

New in V 1.43:

New in V 1.5:

New in V 1.6:

Buttons locked, if not required in selected transmission mode. This ensures, that no variables can be changed "in background"
Automatic joystick zero point calibration after transmitter was switched on. This ensures, that you always have precise zero points, even if your potentiometers are not exacltly linear.

New in V 1.7:

Support for 2 channel car style transmitters with steering wheel
The transmitter type can be seletced in the new "transmitterConfig.h" file
The potentiometers in some transmitters hit the mechanical endstop before the end of the electrical range is reached. This can now be compensated with the "range" variable

New in V 1.8:

In most car style transmitters, the reverse range of the throttle potentiometer is smaller than the forward range.
The reverse range is now multiplied by 4, to solve this problem

New in V 1.9:

The "RC_Tester" functionality (https://github.com/TheDIYGuy999/RC_Tester) is now intergrated
Useful, if you have more than one transmitter. Allows to visualize all 5 analog channels of your transmitter. The radio connection can be easily tested this way.
Press "Select" during power on. The splash screen shows "Micro RC Tester" instead of "Micro RC Transmitter" and then a graphical screen, which visualizes all analog channels
Works fo all 10 vehicle addresses

New in V 2.0:

You have crashed your RC car? Then just play a little PONG session on your transmitter!
Press "Back" during power on. The transittter is then activating the game mode :-)
Press the "Back" button again to restart the game after "Game Over" is displayed

New in V 2.01:

A serious bug in the mapJoystick() function was found during tests with the upcomming STM32 version
The inverse and scale functionality did not work anymore since V2.0
The bug is now solved and you can use the adjustments menu again

New in V 2.1:

3CH configuration for "car style" transmitter with additional 3 position switch added
Used for 3 speed gearbox operation, using a single pole, double throw switch, connected to pin A0. Two resistors from A0 to GND and VCC allow 3 servo positions

New in V 2.2:

3CH configuration for WLtoys A959 etc. based 3+1CH transmitter (CONFIG_WLTOYS) See pictures below.
Support for 3 position double throw switches (for gearbox switching etc.) added. Use two identical resistors (ca. 20k) from GND to center pin to VCC across the switch. Define a "CH1Switch" etc. variable., if a switch instead a potentiometer is connected
New potentiometer calibration variable "reverseEndpoint" allows to adjust the throttle reverse range. Use the "Micro RC Tester" mode on a 2nd transmitter and then adjust the "range" variable as well, until the entire range of all channels is used on the graphical display.
New "ledInversed" variable allows to use the stock WLtoys LED, which has a red and a green LED in one housing. The common pin is connected to VCC

New in V 2.3:

2+2CH configurarion for WLtoys transmitter added (CONFIG_WLTOYS)
Allows to connect 3 buttons on CH4
More than 3 buttons would be possible as well, but I ran out of space for more buttons
Wiring see picture

New in V 2.4:

Joystick ranges separatly adjustable for each channel in "transmitterConfig.h". This is required for the conversation of some car style transmitters, because they don't use the entire potentiometer range from end stop to end stop.

New in V 2.5: