Lightt

Control RGBW LEDs over MQTT using ESP8266.

Features

Support for basic PWM output as well as NeoPixel strips
Full white-channel support
Silky-smooth crossfading animations
Transition command support
Post-process stage
Dimming curve
Robust and fail-safe WiFi/MQTT connectivity

Getting started

In lightt.ino, set feature_white to your desired value depending on whether you want white channel handling.
Flash the board and connect a device to the resulting AP for configuring WiFi and MQTT settings as below.
For further configuration options, check out WS2812B setup variables and MQTT connection function. By default, the strip is set to GRBW (try GRB for strips with no white channel) and no MQTT credentials are used.

Configuring

Each time the board is powered up, one of two things will happen:

If no known WiFi network is found: An access point will be created. Connect a device to this AP and you'll be redirect via captive portal to configure WiFi and MQTT settings. The device will reboot once a new WiFi network has been configured.
If a known WiFi network is found: The device will connect to WiFi. For the following minute, you'll be able to access the configuration options by going to the ESP's IP address in a web browser. One minute after power-on (or when you click the "save" button in the web interface), the board will leave configuration mode and try to connect to MQTT. You may need to power cycle the board if this happens before you were able to save settings.

ESP settings

I'm using the ESP LED Strip Board from Electrodragon. The following IDE settings work well for flashing:

{
    "board": "esp8266:esp8266:generic",
    "configuration": "xtal=80,vt=flash,exception=enabled,ResetMethod=ck,CrystalFreq=26,FlashFreq=40,FlashMode=qio,eesz=4M1M,led=2,ip=lm2f,dbg=Disabled,lvl=None____,wipe=none,baud=115200",
    "port": "COM7",
    "sketch": "lightt.ino",
    "output": "../build"
}

The AVR ISP programmer works well. Ensure you select a board with SPIFFS storage enabled (the eesz=4M1M in the json above should sort that out for you).

Configuring the broker

I run Eclipse Mosquitto in a Docker container based on the official Eclipse Mosquitto Docker image. This is running on an Odroid HC2. In my case I've docker-composed the image with Home Assistant to make a tidy pairing.

MQTT message format

Command: Lightt expects a string consisting of several groups, where each group is a character followed by three numbers. hello

Configuring Home Assistant

Home Assistant is my Home Automation software of choice. These lights are mqtt_template type lights because this enables transition support.

MQTT

Put the following in your configuration.yaml:

mqtt:
  broker: 127.0.0.1

RGB light

light deskback:
  - platform: mqtt_template
    name: "Desk surround light"
    retain: true
    qos: 1
    state_topic: "tenbar/abedroom/deskback/state"
    command_topic: "tenbar/abedroom/deskback/command"
    availability_topic: "tenbar/abedroom/deskback/availability"
    command_on_template: "s001
      {%- if brightness is defined -%}
      {{ 'l%03d' | format(brightness) }}
      {%- endif -%}
      {%- if red is defined and green is defined and blue is defined -%}
      {{ 'r%03dg%03db%03d' | format(red, green, blue) }}
      {%- endif -%}
      {%- if transition is defined -%}
      {{ 't%04d' | format(transition) }}
      {%- endif -%}"
    command_off_template: "s000
      {%- if transition is defined -%}
      {{ 't%04d' | format(transition) }}
      {%- endif -%}"
    state_template: "{% if '1' in value.split(',')[0] %}on{% else %}off{% endif %}"
    brightness_template: "{{ value.split(',')[1] }}"
    red_template: "{{ value.split(',')[2] }}"
    green_template: "{{ value.split(',')[3] }}"
    blue_template: "{{ value.split(',')[4] }}"

RGBW light

light desktop:
  - platform: mqtt_template
    name: "Desktop light"
    retain: true
    qos: 1
    state_topic: "tenbar/abedroom/desktop/state"
    command_topic: "tenbar/abedroom/desktop/command"
    availability_topic: "tenbar/abedroom/desktop/availability"
    command_on_template: "s001
      {%- if brightness is defined -%}
      {{ 'l%03d' | format(brightness) }}
      {%- endif -%}
      {%- if red is defined and green is defined and blue is defined -%}
      {{ 'r%03dg%03db%03d' | format(red, green, blue) }}
      {%- endif -%}
      {%- if white_value is defined -%}
      {{ 'w%03d' | format(white_value) }}
      {%- endif -%}
      {%- if transition is defined -%}
      {{ 't%04d' | format(transition) }}
      {%- endif -%}"
    command_off_template: "s000
      {%- if transition is defined -%}
      {{ 't%04d' | format(transition) }}
      {%- endif -%}"
    state_template: "{% if '1' in value.split(',')[0] %}on{% else %}off{% endif %}"
    brightness_template: "{{ value.split(',')[1] }}"
    red_template: "{{ value.split(',')[2] }}"
    green_template: "{{ value.split(',')[3] }}"
    blue_template: "{{ value.split(',')[4] }}"
    white_value_template: "{{ value.split(',')[5] }}"

Automation ideas

I setup a wake-up light. It's pretty cool.

script:
  wake_up:
    alias: Wake up
    sequence:
      - alias: Surround to red
        service: light.turn_on
        data:
          entity_id: light.desk_surround_light
          brightness: 255
          rgb_color: [255,63,0]
          transition: 800
      - alias: Top to orange
        service: light.turn_on
        data:
          entity_id: light.desktop_light
          brightness: 195
          white_value: 72
          rgb_color: [255,125,0]
          transition: 800
      - delay:
          seconds: 901
      - alias: Surround to blue
        service: light.turn_on
        data:
          entity_id: light.desk_surround_light
          brightness: 255
          rgb_color: [0,255,255]
          transition: 900
      - alias: Top to light green
        service: light.turn_on
        data:
          entity_id: light.desktop_light
          brightness: 255
          white_value: 231
          rgb_color: [0,255,63]
          transition: 900

This gets called every morning from an automation:


automation: 
  - alias: 'Wake-up light (weekday)'
    trigger:
      platform: time
      at: '07:30:00'
    condition:
      - condition: time
        weekday:
        - mon
        - tue
        - wed
        - thu
        - fri
      - condition: state
        entity_id: group.albert_bedroom
        state: 'off'
    action:
      service: script.turn_on
      entity_id: script.wake_up
  - alias: 'Wake-up light (weekend)'
    trigger:
      platform: time
      at: '08:45:00'
    condition:
      - condition: time
        weekday:
        - sat
        - sun
      - condition: state
        entity_id: group.albert_bedroom
        state: 'off'
    action:
      service: script.turn_on
      entity_id: script.wake_up

albertnis / lightt

readme