issues
search
jsaintrocc
/
myblvmgncube
These are my notes on building my MGN BLV CoreXY printer. I hope this work helps others in building their own printers.
Other
11
stars
0
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Consider adapting to a BLVoron
#51
jsaintrocc
opened
2 years ago
0
Add Fire Suppression System
#50
jsaintrocc
opened
2 years ago
0
Use Serial interface of BTT TFT via rPi
#49
jsaintrocc
opened
2 years ago
14
Add missing Fan step
#48
jsaintrocc
closed
2 years ago
0
30 add instruction on squaring your x axis against the front tensioners
#47
jsaintrocc
closed
2 years ago
0
9 combine and revise the print settings.md
#45
jsaintrocc
closed
2 years ago
0
Replace Extruder__-_bontech_Rear_mount.stl with a smaller alternate
#44
jsaintrocc
opened
2 years ago
0
Try out the EVA extrudor
#43
jsaintrocc
opened
2 years ago
1
39 switch to a google spreadsheet for the bom
#42
jsaintrocc
closed
2 years ago
0
Add Controller Fan Mount Step to Step 21
#41
jsaintrocc
closed
2 years ago
1
13 document control board setup
#40
jsaintrocc
closed
2 years ago
0
Switch to A Google Spreadsheet for the BoM
#39
jsaintrocc
closed
2 years ago
0
Document Initial Printer Calibration
#38
jsaintrocc
opened
2 years ago
0
TFT Firmware Setup
#37
jsaintrocc
opened
2 years ago
0
Document Marlin Config
#36
jsaintrocc
opened
2 years ago
1
Document Raspberry Pi/SKR Board Configuration
#35
jsaintrocc
opened
2 years ago
0
Try out klicky probe
#34
jsaintrocc
opened
2 years ago
1
Try out the hextrudort extruder
#33
jsaintrocc
opened
2 years ago
1
Consider Switching to AsciiDoc and github Pages
#32
jsaintrocc
opened
2 years ago
0
Add lubrication for Z lead screws
#31
jsaintrocc
opened
3 years ago
0
Add instruction on squaring your X-axis against the front tensioners
#30
jsaintrocc
closed
2 years ago
3
Redesign X endstop mount to allow better clearance
#29
jsaintrocc
opened
3 years ago
0
Adding the wifi switch for Octoprint Power Control
#28
jsaintrocc
opened
3 years ago
0
17 front panel instructions
#27
jsaintrocc
closed
3 years ago
0
Review and adapt BLV klipper instructions
#26
jsaintrocc
opened
3 years ago
2
Broken STL links
#25
jsaintrocc
closed
2 years ago
2
Fix broken plate vs bracket images
#24
jsaintrocc
closed
2 years ago
1
Consider AC relay to energize future Bed SSR
#23
jsaintrocc
opened
3 years ago
3
Consider Thermally modified power supply fan
#22
jsaintrocc
opened
3 years ago
0
Add Built in Smoke Detector for Safety
#21
jsaintrocc
opened
3 years ago
2
10 missing y endstop
#20
jsaintrocc
closed
3 years ago
0
Update BoM with better linear rails
#19
jsaintrocc
closed
2 years ago
1
12 heatbed wiring
#18
jsaintrocc
closed
3 years ago
0
Write Documentation for Front Panel
#17
jsaintrocc
closed
3 years ago
1
Revise Bed Spring Setup
#16
jsaintrocc
opened
3 years ago
0
Fix all the broken stl links in the guide
#15
jsaintrocc
closed
2 years ago
1
Add Shim to BLTouch Install
#14
jsaintrocc
opened
3 years ago
4
Document Controller Boards Installation and Wiring
#13
jsaintrocc
closed
2 years ago
2
Create Cable Management System for Heated Bed Wires
#12
jsaintrocc
closed
3 years ago
1
For back corners install with printer laying on it's back
#11
jsaintrocc
opened
3 years ago
0
Missing Y-endstop
#10
marutter
closed
3 years ago
4
Combine and revise the printSettings.md
#9
jsaintrocc
closed
2 years ago
0
Block shields need captive nuts to properly secure grill
#8
jsaintrocc
opened
3 years ago
0
Redesign the hotend grill to be easier to print
#7
jsaintrocc
opened
3 years ago
1
Modify cable lockers on Hotend and frame to properly handle 13mm ID conduit.
#6
jsaintrocc
closed
3 years ago
1
Consider Better Cable Management Strategy
#5
jsaintrocc
opened
3 years ago
1
Better way to align bed frame holder
#4
jsaintrocc
opened
3 years ago
0
Missing 2 M3x10 mm in step 8?
#3
marutter
closed
3 years ago
4
Add Nut trap to bed mount
#2
jsaintrocc
opened
3 years ago
0
Add EU supplier for LDO Linear Bearings
#1
jsaintrocc
closed
3 years ago
1
Next