issues
search
opulo-inc
/
feeder
Source for LumenPnP Feeders
Other
99
stars
39
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Schematic and PCB update
#45
G-Pereira
opened
1 month ago
0
Image of the right-angle N20 motor in BOM doesn't match with CAD
#44
ResRipper
opened
2 months ago
0
Feeder frame nut counterbores
#43
ashlynblack
closed
3 months ago
1
tape uptake guide 'nub' partially detatched.
#42
morganrallen
opened
9 months ago
0
Countersunk Holes not called out in design files
#41
MattStep90
opened
11 months ago
0
Filament note unecessary/for different project for html bom
#40
thawney
opened
11 months ago
0
Improve electrolytic cap placement and packages
#39
tanaes
opened
1 year ago
1
U4 deprecated
#38
qwertymodo
opened
1 year ago
0
U1 and U2 are overlayed in the KiCad File and USart1 is not straight from the footprint
#37
Luckywinner
closed
9 months ago
1
Assembly jigs not available
#36
phsete
opened
1 year ago
0
Hi, Please tell the Motor Voltage, output Load torque and stall torque and number of Encoder pulses in the BOM too. thanks for sharing
#35
myjtag
closed
9 months ago
1
Reconsideration of the whole power subsystem.
#34
willyvmm
opened
1 year ago
1
Boards with nothing on some layers should have at least something to prevent fab confusion
#33
sphawes
opened
1 year ago
0
Rotate Board in PCB Editor by 180˚
#32
FL140
closed
1 year ago
1
Add eFuse protection to the +VDC(+24V) Feeder input pin
#31
FL140
closed
1 year ago
1
Redesign so standard M3x14 can be used instead of non standard M3x15.
#30
FL140
opened
1 year ago
1
Fix Motor Drivers Bulk Capacitor Values (Rev.12 Branch)
#29
FL140
closed
1 year ago
1
BoM Fixes (Rev.12 Branch)
#28
FL140
opened
1 year ago
1
Feeder Documentation - Updating Feeder Firmware
#27
KC0D
closed
1 year ago
1
Remove copper pour under spring connector on main board.
#26
qwertymodo
opened
1 year ago
3
NRST/RESET line doesn't require a pull-up resistor
#25
stuartpittaway
closed
1 year ago
2
Circuit to 3D printed part clearances too low
#24
Magpie-81
opened
1 year ago
0
HTML BoM in latest release lists incorrect fastener QTYs
#23
unpaid-bill
closed
1 year ago
1
Setting proper design rules in KiCAD
#22
Magpie-81
opened
1 year ago
1
Reconsider the dual footprint MCU
#21
Magpie-81
opened
1 year ago
4
Filter user input switch signals
#20
unpaid-bill
opened
1 year ago
1
Add options for X- and Y- capacitors to RS485 data lines
#19
Magpie-81
opened
1 year ago
4
Add pull-down resistor to the RS485 driver enable signal
#18
Magpie-81
opened
1 year ago
4
Option to use I2C on the feeder board
#17
Magpie-81
opened
1 year ago
2
Missing capacitor on the reset signal (EMI hardening)
#16
Magpie-81
opened
1 year ago
4
Use a slower RS485 transceiver
#15
Magpie-81
opened
1 year ago
2
Vias in pads need to be avoided
#14
Magpie-81
opened
1 year ago
3
Improve Decoupling Cap Placement/Amount
#13
CurlyTaleGames
opened
1 year ago
7
Simplify BOM, One 24V to 10V Buck/Boost Converter, and Atmega328
#12
CurlyTaleGames
closed
1 year ago
4
No inrush current protection
#11
sphawes
opened
1 year ago
17
Include PDF schematics on the appropriate folders
#10
FailSafinho
closed
1 year ago
1
Schematic symbol for RGB LED on Mobo incorrect
#9
unpaid-bill
opened
1 year ago
1
Flaw in 1-Wire protection circuit
#8
unpaid-bill
opened
1 year ago
8
Diffuser and fiducial should be panelized
#7
qwertymodo
closed
1 year ago
1
Feeder Floor gerbers are only for board 50, not the full panel
#6
qwertymodo
opened
1 year ago
2
Route RS485 as differential pair
#5
G-Pereira
opened
1 year ago
3
Changes to MCUs used
#4
G-Pereira
closed
1 year ago
1
Trim PCB artwork
#3
theacodes
closed
1 year ago
0
Add PCB artwork
#2
theacodes
closed
1 year ago
1
rev07b pcb: connect B0,B2 (with 5mil traces, all that would fit). Fix C16 footprint.
#1
ObviousInRetrospect
opened
2 years ago
0