softerhardware Hermes-Lite issues

softerhardware / Hermes-Lite

Deprecated project!!! See Hermes-Lite2 at main web site

http://www.hermeslite.com

54 stars 40 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

fix error on last data byte of wideband and receiver packets

#64 ahopper closed 7 years ago
1
Use TxPGA directly

#63 in3otd closed 8 years ago
1
V2PA: Investigate heat sink options for enclosure.

#62 AC9HY opened 9 years ago
1
V2PA: Need to use Kicad transmission line tool to implement TX-IN and TX-OUT rails

#61 AC9HY opened 9 years ago
0
V2PA: Need to investigate use of Coilcraft 1812 SMT inductors

#60 AC9HY opened 9 years ago
0
RTL: Proper drive for external signals

#59 softerhardware closed 9 years ago
1
Firmware: Noise floor numbers with 50 Ohm on RX are very different from v1.2

#58 softerhardware closed 9 years ago
1
Firmware: Adjust SDC to minimize ethernet tx sync errors on SDK

#57 softerhardware opened 9 years ago
0
Firmware: Check Frequency Calibration/Computation

#56 softerhardware opened 9 years ago
0
Firmware: Spurs appear transmitting at 28.1 at 33.4 MHz

#55 softerhardware opened 9 years ago
0
Firmware: AD9866 LPF hooked up to ALEX or J16 settings

#54 softerhardware opened 9 years ago
1
Firmware: TX gain hooked up to Hermes TX gain protocol

#53 softerhardware closed 9 years ago
1
Firmware: Software overload and ADC overload don't match

#52 softerhardware closed 9 years ago
1
Revert "Added UNL2003 and connectors"

#51 softerhardware closed 9 years ago
0
Added UNL2003 and connectors

#50 AC9HY closed 9 years ago
1
Hardware: Standoffs, enclosure

#49 softerhardware opened 9 years ago
0
Hardware: Better power supply

#48 softerhardware opened 9 years ago
4
All: Documentation and "marketing"

#47 softerhardware opened 9 years ago
0
Hardware: Hermes-Lite 2.0

#46 softerhardware opened 9 years ago
0
Software: GNU Radio module

#45 softerhardware opened 9 years ago
1
Hardware: Improve assembly, production and kitting of v1.2

#44 softerhardware opened 9 years ago
0
Software: Attract developers

#43 softerhardware opened 9 years ago
0
Firmware: Hooks and better control for software

#42 softerhardware closed 9 years ago
1
All: Enable PureSignal

#41 softerhardware opened 9 years ago
0
Firmware: Pull direct audio out by IK1XPV

#40 softerhardware opened 9 years ago
0
All: Frontend with PA, TR switch and filters

#39 softerhardware opened 9 years ago
0
All: VNA functionality

#38 softerhardware opened 9 years ago
0
Firmware: Review and fix Quartus warnings

#37 softerhardware opened 9 years ago
0
Firmware: Update to Latest Hermes Firmware

#36 softerhardware opened 9 years ago
0
Firmware: No 384kHz with new 61.44MHz crystal

#35 softerhardware closed 9 years ago
1
Firmware: ASMI interface not working on CV

#34 softerhardware opened 9 years ago
0
PCB: Standoffs

#33 softerhardware closed 9 years ago
1
PCB: Power supply

#32 softerhardware closed 9 years ago
2
PCB: RF Front-end

#31 softerhardware closed 9 years ago
1
Wire from VIN to VIN not routed on board.

#30 frohro closed 10 years ago
1
PCB: Noise considerations

#29 softerhardware closed 9 years ago
4
PCB: Flood ground on component and solder side

#28 softerhardware closed 10 years ago
1
All: 6M

#27 softerhardware opened 10 years ago
1
RTL: Port to BeMicro CV

#26 softerhardware closed 9 years ago
2
PCB: More power, RX/TX switch

#25 softerhardware closed 10 years ago
1
All: RX and TX Measurements

#24 softerhardware opened 10 years ago
0
All: Port HiQSDR

#23 softerhardware opened 10 years ago
0
PCB: Max power is 17 dBm

#22 softerhardware closed 10 years ago
1
PCB: Improve power sharing with BeMicro SDK

#21 softerhardware closed 10 years ago
1
PCB: Dip switch is extra expense

#20 softerhardware closed 9 years ago
2
PCB: Jumpers required for AD9866 SPI buss

#19 softerhardware closed 9 years ago
2
PCB: PCI-E connector not needed

#18 softerhardware closed 9 years ago
2
PCB: Wrong footprint for C25 and C22

#17 softerhardware closed 9 years ago
1
PCB: Clock requires jumper

#16 softerhardware closed 9 years ago
1
PCB: Prototype works only with a 5V supply

#15 softerhardware closed 10 years ago
1