AdityaSantosh aeroquad issues

AdityaSantosh / aeroquad

Automatically exported from code.google.com/p/aeroquad

0 stars 0 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

BMP085 pressure reading code uses non initialised variables

#46 GoogleCodeExporter closed 8 years ago
2
Optimize EEPROM Writes

#45 GoogleCodeExporter closed 8 years ago
1
In readEEPROM the calls to receiver.setTransmitterSlope and receiver.setTransmitterOffset are nonsense

#44 GoogleCodeExporter closed 8 years ago
2
class FlightAngle_DCM has no member named 'get'

#43 GoogleCodeExporter closed 8 years ago
2
PID dTerm calculation does not use delay since last call

#42 GoogleCodeExporter closed 8 years ago
1
Milli second accuracy used in loop() to set G_Dt is not sufficient, introducing 33-50% error in updating control values.

#41 GoogleCodeExporter closed 8 years ago
1
Check v1.7 shield orientations work with v2.1 flight software

#40 GoogleCodeExporter closed 8 years ago
1
Make a smaller version of the configurator screen for Netbooks

#39 GoogleCodeExporter opened 8 years ago
5
getGyroAngle in FlightAngle.h is buggy

#38 GoogleCodeExporter closed 8 years ago
1
for-loop bug in flightangle.h

#37 GoogleCodeExporter closed 8 years ago
1
FlightAngle.h: Missing DCM Kp & Ki definitions for 1.7 shield w/ ADXL 335

#36 GoogleCodeExporter closed 8 years ago
3
accelScaleFactor definition in Mega_V2 class and _v1 class are swapped.

#35 GoogleCodeExporter closed 8 years ago
1
Wrong gyroScaleFactor for Gyro_AeroQuad_v1 in 2.0.x

#34 GoogleCodeExporter closed 8 years ago
1
Accel Z Indication 90 degrees off (Mega, 1.7, IXZ500, v2,0.1, 2.5 Config

#33 GoogleCodeExporter closed 8 years ago
1
Wii sensor problems: after calibration gyro roll & pitch are 45 / -45 (not 0). Gyro jaw data is reversed.

#32 GoogleCodeExporter closed 8 years ago
1
Motor XConfig view in configurator

#31 GoogleCodeExporter closed 8 years ago
1
Raw Sensor Data graph the Y scale is huge and changing the scale is not persistant

#30 GoogleCodeExporter closed 8 years ago
2
Raw Sensor Data / 'Q' command only showing values for Rol and Pitch

#29 GoogleCodeExporter closed 8 years ago
1
Document C++ Class Approach

#28 GoogleCodeExporter closed 8 years ago
1
Change PID into a C++ Class

#27 GoogleCodeExporter closed 8 years ago
1
Fix accel/gyro engineering units

#26 GoogleCodeExporter closed 8 years ago
1
Implement MixerTable in Flight Software and Configurator

#25 GoogleCodeExporter opened 8 years ago
3
Add servo configuration to the Configurator

#24 GoogleCodeExporter opened 8 years ago
2
Receiver.pde assignment instructions

#23 GoogleCodeExporter closed 8 years ago
1
Configurator - Export Settings to File

#22 GoogleCodeExporter opened 8 years ago
1
Adjust gyro bias in real time flight

#21 GoogleCodeExporter closed 8 years ago
2
Re-check localized decimal usage for Mac Configurator

#20 GoogleCodeExporter closed 8 years ago
2
Add servo control to Flight Software

#19 GoogleCodeExporter closed 8 years ago
4
Investigate adding Wii sensor to AeroQuad flight software

#18 GoogleCodeExporter closed 8 years ago
1
Fix NaN values in transmitter cal if not calibrating all channels

#17 GoogleCodeExporter closed 8 years ago
1
Add PPM pulse train receiver option

#16 GoogleCodeExporter opened 8 years ago
8
Transmitter is dead

#15 GoogleCodeExporter closed 8 years ago
2
Verify correct telemetry is sent for filtered transmitter values

#14 GoogleCodeExporter closed 8 years ago
4
Add auto hover capability using accelerometer/sonar/baro

#13 GoogleCodeExporter opened 8 years ago
3
Add remote commanding capability

#12 GoogleCodeExporter opened 8 years ago
2
Add remote commanding capability

#11 GoogleCodeExporter opened 8 years ago
6
Baud Rate

#10 GoogleCodeExporter closed 8 years ago
1
Updated angle calculation may be returning 0 for gyros

#9 GoogleCodeExporter closed 8 years ago
1
Add comment to show compatibility for IDG300 and IDG500

#8 GoogleCodeExporter closed 8 years ago
1
Add exponential transmitter curve capability

#7 GoogleCodeExporter opened 8 years ago
5
Unable to complete transmitter calibration if no channels 5 & 6

#6 GoogleCodeExporter closed 8 years ago
1
User forced to run as Administator under Windows Vista/7

#5 GoogleCodeExporter closed 8 years ago
1
Don't allow user to exit while Configurator is reconnecting to AeroQuad

#4 GoogleCodeExporter closed 8 years ago
2
Default flight connection screen to show gyro indicators and motor plots

#3 GoogleCodeExporter closed 8 years ago
2
Motor Commmands show inverted

#2 GoogleCodeExporter closed 8 years ago
3
Force sending of '.' instead of ',' when using a non-English version of Windows

#1 GoogleCodeExporter closed 8 years ago
4