An easy-to-use interface to the NXP Sensor Fusion version 7 algorithms, providing orientation data derived from a 9 degrees-of-Freedom motion sensor.
It is configured to work with the Adafruit breakout board #3643 using the NXP FXOS8700 magnetometer/accelerometer and FXAS21002 gyroscope sensor ICs, but can be modified to work with other sensors having an I2C interface. With additional modification, it can also work with SPI interface sensors.
The library runs on Espressif's ESP32 and ESP8266 processors. Library output is via Get___()
methods that return the various orientation parameters (e.g. GetHeadingDegrees(void)
,
GetPitchDegrees(void)
, GetAccelXGees(void)
, etc). A choice of units is provided
(e.g. Degrees, Radians, quaternions, Gees or m/s^2). The IC temperature is also available.
An example main.cpp
(see examples/fusion_text_output.cc
) illustrates how to use
this library, and outputs orientation data in text format using serial and WiFi
interfaces. For a slightly more complex example, see the adjunct library
https://github.com/BjarneBitscrambler/SignalK-Orientation
which uses this one to generate the orientation data, then packages it up and sends it
via WiFi to a Signal K server.
A C++ class (src/sensor_fusion_class.h
) provides simple access to the most common
sensor fusion functions, but it is also possible to directly interface with the library
methods contained in the underlying C files, which are based on those provided
by NXP in their version 7.20 release.
Orientation sensing using combined accelerometer + gyroscope + magnetometer sensors has become quite accurate when coupled with the right sensor fusion software. NXP manufactures these types of sensors, and have written an excellent sensor fusion library for their Kinetis 32-bit microcontrollers. Their library, which is released under the BSD-3-Clause license, was ported in 2015 to the Arduino environment by Adafruit as their AHRS (Attitude and Heading Reference System). The AHRS port uses NXP's version 4.2 fusion code.
A newer version of the NXP sensor fusion library (version 7.2) is available, which is what this present project is using. This newer library has several improvements, including the ability to perform magnetic calibration while in use (as opposed to needing a separate software tool).
My motivation for porting NXP's library is to create an orientation sensor for marine use, using off-the-shelf hardware and the Signal K / SensESP project to provide orientation data (e.g. magnetic heading, roll, and pitch) on a vessel. I have targeted this project for the Espressif ESP32/ESP8266 microcontrollers and the NXP sensors.
The present software works with the NXP 9DOF (9 Degrees-Of-Freedom) sensor combination consisting of FXOS8700 magnetometer + accelerometer and FXAS21002 gyroscope. These are conveniently available mounted together on the Adafruit #3463 breakout board.
Other sensors could be used. Note that only the I2C interface has been implemented and tested; a SPI interface is possible with additional work and testing.
The present software is written for the ESP32 and ESP8266 processors. With some rewriting of the I2C and timing routines, the code can be ported to other processors.
The fusion code and associated project files have been written for and tested in the PlatformIO development environment, as an Arduino framework project on an ESP32 board and on an ESP8266 board.
In addition to the standard Arduino environment, this project uses the following libraries which are automatically installed in the Arduino framework:
docs/html/index.html
file in your favourite browser. Documentation is auto-generated from comments in the code itself, using Doxygen. Use the Issues and Pull Request tabs on this project's Github repository if you have suggestions or wish to contribute to this project.
To use this library follow these steps (some untested - let me know of any changes you needed to make to get things to work on your setup):
Espressif ESP-WROVER-KIT
and Framework: Arduino
(other ESP32 boards should work without changes; as does the d1_mini board with Espressif's ESP8266 CPU)Now follow either of these two methods to bring in the library files:
/src
into your new project's /src
folder. Ensure you get all the files as well as the subfolder /src/sensor_fusion
./examples/fusion_text_output.cc
into your new PlatformIO project's /src
folder. You may want to rename it main.cc
or main.cpp
to remind yourself that it contains the setup()
and loop()
functions./examples/fusion_text_output.cc
into your new PlatformIO project's /src
folder. You may want to rename it main.cc
or main.cpp
to remind yourself that it contains the setup()
and loop()
functions.platformio.ini
into your new project's root directory (or use it to modify the relevant sections in your own project's platformio.ini
). Locate the section lib_deps =
and add the line https://github.com/BjarneBitscrambler/OrientationSensorFusion-ESP.git. Method 2 results in the library code being imported into PlatformIO's .pio
folder.
Then:
platformio.ini
file for your specific board and environment. Use this project's platformio.ini
file as an example.#defines
at the top of your fusion_text_output.cc
(the sample main.cc
) to reflect your particular hardware. The I2C pins connecting your processor to your sensor ICs will likely be different, and you may also need to change the I2C addresses that the ICs are configured for.To confirm that the software is communicating with your sensors, observe the serial port output of the ESP processor. Use a USB connection to a PC running a terminal program at 115200 baud, 8 bits, No parity, 1 stop bit. Several progress messages should appear as the fusion software configures the sensors. Once the algorithm is running, lines of text containing a timestamp and orientation data should scroll by. See the main.cc
program's loop()
for details.
However, the best way to visualize operation of the orientation algorithm is by using the NXP Sensor Fusion Toolbox.
The out-of-the-box software is configured to send data packets containing the sensor fusion results at a rate of 40 Hz over the processor's Serial UART interface (connected to the USB port on my WROVER development kit). These packets are formatted for NXP's Sensor Fusion Toolbox Windows application (available for download from NXP at no cost) which will display the data and can even be used to send commands back to the processor running the fusion algorithms. See the User's Guide under the Help tab of the Toolbox for details.
The Toolbox when working shows a graphic of a PCB rotating on the screen in synchronization with motion of your own board. If there is no motion at all, then check that the data packets are arriving on the expected COM: port of your computer. A terminal program (like HyperTerminal or PuTTY) can help display traffic on a COM: port, but note that the data packets are in binary format (not ASCII text) so you won't be able to interpret them visually. If the Toolbox shows motion but it is jerky or reversed from the actual board motion, then likely one or more of your board's axes are not oriented according to how the fusion software expects. Different sensor board manufacturers will have placed the sensor ICs in orientations particular to their own needs. The file hal_axis_remap.c
is used to invert or swap axes to conform to what the fusion algorithm expects. For more details, see that file, and also NXP's Application Note AN5017 (Coordinate Systems).
Because testing an orientation sensor with a USB cable tethering it to your development computer is a pain, the software also supports streaming the data over WiFi. In the main setup()
code, a WiFi AP (Access Point) is started, which means the ESP processor will broadcast its SSID and you should be able to connect to it with your development system using the password you provide in the main.cc
file. Once a WiFi connection is established, you can open a TCP connection to port 23 of the ESP and the orientation data will then stream over your TCP connection. A few hints:
telnet 192.168.4.1
, where you replace the example IP address with the one the ESP has indicated in its serial output. I did earlier try having the ESP connect as a client to our WiFi router, rather than acting as an AP itself. Unfortunately, this caused delays in delivery of the streamed traffic that would intermittently freeze the Sensor Toolbox. Performing a ping
from the development computer to the ESP showed trip times sometimes exceeded 1000 ms when going through the router. So, using the ESP as an AP is better for timely data delivery on my hardware.
Using WiFi (even when ESP is acting as AP) does introduce noticeable lag in the Toolbox graphic response, compared to a USB connection. It looks like about a 200 ms lag on my system.
You can use the GPIO output that toggles each time through the data collection and sending loop to confirm whether your ESP is collecting and transmitting data regularly. Using the default software, the output should toggle every 25 ms (i.e. a 20 Hz square wave). See fusion_text_output.cc
for details.
The file/sensor_fusion/build.h
contains defines for various functionality, such as whether the software outputs its data via hardware serial UART or WiFi TCP connections, or both (default). Edit this file as desired, but note that not all combinations of features may be valid or been tested.
Changes to adapt to other hardware are confined to a few files, as the majority of the fusion code is generic C-code that is pretty platform-independent.
Files that would be expected to change when using different hardware are the hal_*.*
files, board.h
, and build.h
. As well, new sensor IC driver files may be needed, patterned on the existing driver_fxos8700.*
and driver_fxas21002.*
files. Finally, calibration_storage.*
may need changing depending on how non-volatile memory functions on the different hardware.
If you want to change how the fusion algorithm operates, have a look at control*.*
, build.h
, and status.*
. Quite a lot of parameters are selected via pre-processor #define
statements; check the comments for suggestions on how to achieve your goals.
Bjarne Hansen
Copyright (c) 2020, Bjarne Hansen All rights reserved.
SPDX-License-Identifier: BSD-3-Clause