mrAyaz ardupilot-mega issues

mrAyaz / ardupilot-mega

Automatically exported from code.google.com/p/ardupilot-mega

0 stars 0 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Relay not found after 2.27 update

#469 GoogleCodeExporter closed 8 years ago
5
APM Planer 1.1.16 / Firmware upload fails / Check port settings or port in use..... .....ArdupilotMega.GCSViews.Firmware.UploadFlash(String filename, String board)

#468 GoogleCodeExporter closed 8 years ago
2
Crosstrack should be a PID

#467 GoogleCodeExporter opened 8 years ago
3
Nav roll PID is inappropriately scaled by ground speed.

#466 GoogleCodeExporter closed 8 years ago
4
Modes not showing correctly in Mission Planner

#465 GoogleCodeExporter closed 8 years ago
4
Flight Modes issue - APM remain in MANUAL mode after switch

#464 GoogleCodeExporter opened 8 years ago
8
DataFlash_test.cpp does not compile

#463 GoogleCodeExporter closed 8 years ago
1
APM Planner does not allow you to revert to a previous version/s of the firmware.

#462 GoogleCodeExporter closed 8 years ago
2
APM must not feed servos, any pulse width which is either higher or lower than the present radio Transmitter

#461 GoogleCodeExporter opened 8 years ago
5
Mission Planner 1113 has poor performance in handling CRC errors in telemetry

#460 GoogleCodeExporter closed 8 years ago
2
Flight Modes switching issue

#459 GoogleCodeExporter closed 8 years ago
4
Joystick Calibration Issue

#458 GoogleCodeExporter closed 8 years ago
2
2Way telemetry is not working in APM2.2.6, however it was working in APM2.12

#457 GoogleCodeExporter closed 8 years ago
3
Running error in Mission Planner on Windows, XP, SP3

#456 GoogleCodeExporter closed 8 years ago
4
Arduino Mega

#455 GoogleCodeExporter closed 8 years ago
2
Simple mode does not work anymore

#454 GoogleCodeExporter closed 8 years ago
2
add avr-size output target to makefile

#453 GoogleCodeExporter closed 8 years ago
1
arduino.mk not ready for arduino IDE version 1.00

#452 GoogleCodeExporter closed 8 years ago
2
Mission Planner Starting Window Placement

#451 GoogleCodeExporter closed 8 years ago
3
Installation Issue for ArdupilotMegaPlanner (Mission Planner 1.1.1)

#450 GoogleCodeExporter closed 8 years ago
4
Mission Planner FW uploader safety

#449 GoogleCodeExporter closed 8 years ago
1
Setting current sensor offset voltage in APM Mission Planer.

#448 GoogleCodeExporter opened 8 years ago
3
RC4 output driven beyond endstop on ArduPlane startup

#447 GoogleCodeExporter opened 8 years ago
6
MAKE A RECOMMENDATION OF WHAT ESC TO USE WITH THE APM

#446 GoogleCodeExporter closed 8 years ago
1
Mission Planner Zeroes Out Lat, Long, Alt when Converting Waypoint to Loiter Command

#445 GoogleCodeExporter closed 8 years ago
9
on main out put plug only plugs one and two will power the board

#444 GoogleCodeExporter closed 8 years ago
5
Planner "Zoom To" pop-up does it anyway if the Cancel button is pushed.

#443 GoogleCodeExporter closed 8 years ago
3
Incorrect plane heading shown on the ardupilot mega misson planner

#442 GoogleCodeExporter closed 8 years ago
4
Yaw integrator susceptible to wind-up from manual input.

#441 GoogleCodeExporter closed 8 years ago
4
Patch for /zh-Hans/Glossary.wiki

#440 GoogleCodeExporter closed 8 years ago
2
Proble upgrading to firmware v.2.251

#439 GoogleCodeExporter closed 8 years ago
3
CONDITION_CHANGE_ALT only works for ascending.

#438 GoogleCodeExporter closed 8 years ago
6
MAV_CMD_CONDITION_CHANGE_ALT requires absolute altitude

#437 GoogleCodeExporter opened 8 years ago
2
Support for more than 4 axes in Mission Planner from Joystick input

#436 GoogleCodeExporter closed 8 years ago
2
# define CH7_OPTION CH7_SIMPLE_MOD over MP

#435 GoogleCodeExporter closed 8 years ago
9
Rate PID Setting write failing in APM Planner 1.0.82

#434 GoogleCodeExporter closed 8 years ago
7
Mag Declination Value different

#433 GoogleCodeExporter closed 8 years ago
3
mission planner 1.0.79 error

#432 GoogleCodeExporter closed 8 years ago
3
Gyroscope Response Slow

#431 GoogleCodeExporter opened 8 years ago
11
Gyroscope Response Slow

#430 GoogleCodeExporter closed 8 years ago
1
Throttle Failsafe wrong behaviour and fix

#429 GoogleCodeExporter opened 8 years ago
3
Mission Planner do not allow ACM 2 Throttle PI and Throttle Rate P/I adjustments

#428 GoogleCodeExporter closed 8 years ago
2
throttle goes to zero on "Stabilize" and "Auto", OK in "Manual"

#427 GoogleCodeExporter closed 8 years ago
3
Mission Planner APM Firmware Upgrade do not work

#426 GoogleCodeExporter closed 8 years ago
1
Mission Planner should be able to upload arduino compiled code.

#425 GoogleCodeExporter closed 8 years ago
3
Debug Fuses for mega2560?

#424 GoogleCodeExporter closed 8 years ago
3
FastSerial flush bug

#423 GoogleCodeExporter closed 8 years ago
2
Loiter Issue- No Altitude hold off GPS or Sonar

#422 GoogleCodeExporter closed 8 years ago
1
Gain Scheduling

#421 GoogleCodeExporter closed 8 years ago
2
Disable gps lat/lon cells for arducopter commands that don't accept them, like "Land"

#420 GoogleCodeExporter closed 8 years ago
3

Previous Next