teemuatlut TMC2130Stepper issues

teemuatlut / TMC2130Stepper

Arduino library for Trinamic TMC2130 Stepper driver

MIT License

159 stars 50 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

StallGuard can't seems to work while in TMCL-IDE the same config works

#103 jonnydman opened 2 years ago
1
ESP8266 (Wemos D1) in combination with stepper motor driver tmc2310, heat problem and force hold problem.

#102 eleminer opened 2 years ago
1
microsteps() takes power of two values... except at full steps?

#101 i-make-robots opened 3 years ago
0
Motor won't rotate if stealthChop isn't enabled

#100 Robin-12 opened 3 years ago
3
I am not able to Enable LOST_STEP feature

#99 anil5313 opened 3 years ago
3
i am not able to see LOST_STEPS. please help me ...

#98 anil5313 closed 3 years ago
0
Is DIR pin obsolete? / verify current fraction of steps / 1 step function in SPI

#97 Er9y714 closed 3 years ago
2
Possible pull request... Use MCP23017 to multiple SPI TMC2130

#96 julioj4pa closed 4 years ago
7
Issue with higher current rated motors

#95 dev-000 closed 1 year ago
8
TMC2130 Stallguard not working with Arduino UNO

#94 Patrick-Yao-SRE closed 4 years ago
8
Calibrate_spreadCycle - DRV_STATUS() returning 0xFFFFFF

#93 changedsoul closed 4 years ago
1
How to reduce motor vibrations?

#92 MarkMan0 opened 4 years ago
1
Simple example only partially working

#91 Russellfam opened 4 years ago
3
StallGuard Example not working

#90 MilanVDB opened 4 years ago
1
how to setup

#89 goldjunge91 opened 5 years ago
1
Struggling with parameters

#88 margaret-n-m closed 5 years ago
2
readme.md missing reference

#87 i-make-robots opened 5 years ago
2
Reading 256

#86 Rubenkonings closed 5 years ago
0
On driver board end stops

#85 coolerooney opened 5 years ago
3
setting RMS current via SPI & via ref voltage / potentiometer, difference?

#84 csurf closed 3 years ago
3
Cannot properly tune StallGuard Threshold into a functional regime

#83 r-a-i opened 5 years ago
3
stallguard2 & AccelStepper library

#82 csurf opened 5 years ago
2
Trouble getting simple sketch example working ver 2.5.1

#81 Mogwai77 closed 5 years ago
2
Software SPI not working

#80 TillScout opened 5 years ago
2
DIAG0 & DIAG1 pin for stall detection

#79 ziyangwang007 closed 5 years ago
1
set current

#78 ziyangwang007 closed 5 years ago
3
typo's in TMC2130Stepper.h / TMC2130Stepper.cpp (section XDIRECT)

#77 djamu closed 5 years ago
3
Read TSTEP register, but the value is small

#76 ziyangwang007 closed 5 years ago
1
Problems with Stallguard

#75 roelandbenoot opened 5 years ago
8
TMC write is OK, but read doesn't work. the data always be 1111111111111111 or 0xFFFFFF

#74 ziyangwang007 closed 5 years ago
3
TMC 5072 Stallguard problem

#73 SrinivasD18 opened 5 years ago
2
Problem connecting TMC2130 directly to stepper motor

#72 JiGlain closed 5 years ago
0
TMC 4671

#71 charleslemaire0 closed 5 years ago
0
Enable/Disable driver via SPI

#70 orkunkilinc closed 5 years ago
2
Stallguard with AccelStepper Library

#69 martinmatias opened 5 years ago
11
How to control with SPI Mode? (without STEP Pin) Example needed

#68 martinmatias closed 5 years ago
7
Issue with multiple TMC2130

#67 akym closed 5 years ago
4
little need help stallguard and noise

#66 joe318 opened 5 years ago
1
Setup in memory and then push

#65 gvandersel opened 5 years ago
2
How to create function to control motor speed by RPMs?

#64 conn250 opened 5 years ago
1
Stallguard with 2 nema

#63 joe318 closed 5 years ago
8
Reading DRV_STATUS

#62 gvandersel closed 5 years ago
2
Temperature monitor?

#61 robustini opened 5 years ago
1
Problem with Running for Certain Number of Steps

#60 Legohead259 opened 6 years ago
10
Stealtchop stops motor working

#59 SteveWCoder opened 6 years ago
1
Looking for Help With StallGuard

#58 Legohead259 opened 6 years ago
5
Fix for #56: Swap SDI/SDO pads in PCB view

#57 soswow closed 6 years ago
0
TMC2130: SDI and SDO swapped in Fritzing PCB view

#56 eyer1951 opened 6 years ago
10
M122 - Understanding the readings.

#55 MotoGP1199 opened 6 years ago
1
Got TMC2130Stepper library working after 'constexpr' compile errors with STM32 on Arduino IDE

#54 loopyengineeringco opened 6 years ago
3