issues
search
VoronDesign
/
Voron-Trident
Voron Trident CoreXY 3D Printer design
579
stars
173
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Deck Support Clip STL Labeled wrong
#65
AleXthePunK
closed
2 years ago
4
Misspelling in Assembly Manual
#63
blite
closed
2 years ago
2
Wrong position of heat set insert hole on front_skirt_b_350
#62
Promix953
closed
2 years ago
1
Update thermistor definitions to new types
#61
julianschill
closed
2 years ago
1
Mean Well LRS-200-24 Wiring Mismatch
#60
samuraihelmet
closed
2 years ago
0
Add G90 to PRINT_START macro
#59
julianschill
opened
2 years ago
0
Clarify Hall Effect Magnet Installation Process
#58
SkiBikePrint
closed
1 year ago
4
Spider v2.2 interference with mount
#57
poernahi
closed
2 years ago
2
SSR wiring on pg 115 inconsistent with updated switch wiring
#56
BerzerkaDurk
closed
2 years ago
0
Update Assembly_Manual_Trident.pdf
#55
DunarDolorgiet
closed
2 years ago
0
Manual does not specify where 1mm and 3mm tape and respective clips are used on panels.
#54
BerzerkaDurk
closed
2 years ago
0
Cannot Download the .STL files for A or B Drive Frame Lower - Both files appear to be corrupted.
#53
Rwhite692
closed
2 years ago
3
Adding Fysetc controller mounts
#52
stvptrsn
closed
2 years ago
0
Update Trident_Octopus_Config.cfg to fix Z2 direction
#51
emolitor
closed
2 years ago
0
Display housing update
#50
stvptrsn
closed
2 years ago
0
A list of suggestions for the manual from my Trident build
#49
Sparohok1
closed
2 years ago
4
modified [a]_mini12864_case_front_insert to fit BTT mini 12864 V1.0 Display
#48
Markus-1984
closed
2 years ago
3
Assembly manual pg. 273 BHCS
#47
rlaferla
closed
2 years ago
0
XY End-Stop Pod wiring length
#46
etjensen
closed
2 years ago
2
Hot / Neutral Wires reversed on power inlet diagram, page 208
#45
BerzerkaDurk
closed
2 years ago
0
Remove leading spaces from selectable config options
#44
cbc02009
closed
2 years ago
0
Squaring instructions note to move the gantry to A and B drives to square. B drive has protruding Y endstop bracket.
#43
mobilemcclintic
closed
2 years ago
2
Make bed heater and magnet placement more obvious
#42
Lycowolf
closed
2 years ago
0
Voron Manual has live and neutral reversed on 5v PSU
#41
PhoenixMage
closed
2 years ago
0
Update Assembly_Manual_Trident.pdf
#40
DunarDolorgiet
closed
2 years ago
0
Trident assembly manual is low contrast, hard to read
#39
mapsedge
closed
2 years ago
7
TOOLHEAD/XY END-STOP ROUTING (pg 225)
#38
rlaferla
closed
2 years ago
0
Recommended Filtered Power Inlet TE 10EGG1-2 requires two fuses, while BOM only lists one.
#37
leanghoun
closed
1 year ago
1
Manual page 16 "PREPARE 8 EXTRUSIONS" seems incorrect
#36
DanTup
closed
2 years ago
0
The BMG extruder motor needs to be labeled on pg. 155 in the manual.
#35
rlaferla
closed
2 years ago
0
Manual (page 53) needs to point out offset of vertical extrusion
#34
mikem1017
closed
2 years ago
1
Manual (pg 131) needs to specify the connector
#33
rlaferla
closed
2 years ago
0
Octopus config for Trident
#32
cbc02009
closed
2 years ago
5
Created a plain trident config using spider 1.1 board
#31
majarspeed
opened
2 years ago
2
Broken hyperlinks within the Assembly Manual
#30
simonrwatts
closed
2 years ago
1
Assembly and frame upgrade manual needs extrusion access hole drill size.
#29
bwattendorf
opened
2 years ago
0
The Frame upgrade guide should list extrusion lengths for 300 and 350 frames.
#28
bwattendorf
opened
2 years ago
5
Possible confusion on Page 19/20 when not using a 250mm frame size
#27
wattsie
closed
2 years ago
1
MGN 12 trident.
#26
selimayaz
closed
2 years ago
1
Remove references to quad gantry leveling from config files.
#25
cbc02009
closed
2 years ago
2
Include warning about needing a BAT85 diode for the inductive probe depending on control board
#24
ShawnBuckley
closed
2 years ago
0
Export S6 bracket
#23
aaarsene
closed
2 years ago
1
M5 bolts on XY joints are chamfered instead of bridged
#22
henrikssn
closed
2 years ago
8
Typo in the assembly manual
#21
onfoot
closed
2 years ago
0
Panel DXFs seem to have a units issue.
#20
BerzerkaDurk
closed
1 year ago
3
fix: correct z_tilt z_positions
#19
bartlammers
closed
2 years ago
3
Looks like the Assembly Manual file has an issue
#18
BernardG
closed
2 years ago
1
X Carriage Hex Hole Rounded
#17
crashmaxx
closed
2 years ago
2
Homing override fixes
#16
timmit99
closed
2 years ago
0
Wrong extrusion referenced on pg 132
#15
billyclaymyersmsft
closed
2 years ago
2
Previous
Next