synthetos g2 issues - Githubissues

synthetos / g2

g2core - The Next Generation

Other

622 stars 296 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Project status

#516 timonsku opened 5 months ago
5
Is G2core a good choice for my app?

#515 rayz55 opened 1 year ago
0
Which version?

#514 simonemarin closed 1 year ago
15
Endstops behaviour

#513 simonemarin closed 1 year ago
9
Compile g2core for gShield on Windows

#512 Element21302 closed 1 year ago
3
Add PCB design files for Arduino Due Shield

#511 Bozog closed 2 years ago
3
Spindle Enable Pin Not Functioning

#510 mertzk opened 2 years ago
1
Tomash cnc test

#509 tomashx closed 2 years ago
4
UART on g2core

#508 XavierCuenca opened 2 years ago
0
101.03 branch

#507 XavierCuenca closed 2 years ago
3
Status report not returning "pos" or "mpo" for A-axis

#506 FHUGO1 closed 1 year ago
1
Create a output for ATC

#505 martonpetroczki closed 2 years ago
1
Arduino Due with Edge-preview+gShield not working ///'laser_tool' was not declared in this scope///

#504 martonpetroczki closed 2 years ago
4
feedrate interpretation for moves involving both, primary axes (XYZ) and secondary linear axes (UVW) differs from LinuxCNC

#503 DerAndere1 opened 2 years ago
0
Is the g2core project still active?

#502 lutorm closed 1 year ago
1
Revert "Fix U,V,W axis operation, most notably homing, probing and moving with proper feed rates."

#501 ril3y closed 2 years ago
3
Soft Limits not setting alarm state. Not stopping job.

#500 discoordination opened 2 years ago
1
9 axis external driver board

#499 qiwalker closed 2 years ago
1
Spindle sometimes does not enable

#498 lutorm closed 2 years ago
3
Error Compiling: Windows 10 Atmel Studio

#497 toozinger closed 3 years ago
1
[wip] rough sketch of unsigned substep_accumulator mechanism

#496 sjkelly closed 2 years ago
1
G-codes

#495 DmitriiZorin closed 3 years ago
1
Skew correction ideas?

#494 Mgilbride closed 2 years ago
4
Not emitting steps at shallow incline.

#493 lutorm opened 3 years ago
7
Spiral roughing hiccup?

#492 Mgilbride closed 1 year ago
4
Fix U,V,W axis operation, most notably homing, probing and moving with proper feed rates.

#491 prof7bit closed 2 years ago
0
E-Stop set-up on 100.26 and above compiled with gShield pinout?

#490 Mgilbride closed 3 years ago
1
Edge: axis names in text mode position reports (contains patch)

#489 prof7bit opened 3 years ago
0
Edge: U,Y,W axes don't work in probe commands (G38.x)

#488 prof7bit opened 3 years ago
1
edge-preview: missing acceleration/deceleration when sending multiple moves at once

#487 prof7bit opened 3 years ago
1
Wrong enum used for axis configuration

#486 benlaurie opened 3 years ago
1
Fix bouncy probes.

#485 benlaurie opened 3 years ago
0
Bad state after gpio input action stop

#484 dauriata closed 1 year ago
3
Fix bug with default spindle polarity value

#483 justinclift closed 3 years ago
0
Homing on U,V or W axis is not possible

#482 prof7bit opened 3 years ago
36
UVW Axis limit switches, documentation missing, configuration missing

#481 prof7bit opened 3 years ago
7
New “kill” behavior seems inconsistent with State Model for Feedhold and Job Kill (and bad location on hold)

#480 tedh-shopbot opened 3 years ago
0
Status Report requested just before move starts sometimes reports target location rather than current location

#479 tedh-shopbot opened 3 years ago
3
G4 not dwelling with non-movement commands

#478 wholetthedogsout opened 3 years ago
5
TinyG/g2core 4th Axis Post .cps

#477 Johnr24 closed 3 years ago
4
Config fixes for gShield/gquintic

#476 thatch opened 3 years ago
3
Fix acceleration issue after probing cycle

#475 mhlong10 closed 3 years ago
0
Acceleration messed up after G38.2 probing

#474 mhlong10 closed 3 years ago
3
Better jogging support

#473 lllars opened 4 years ago
0
Adjust duration of step pin low state

#472 lllars closed 4 years ago
18
bCNC - autolevel

#471 ziopippona51 closed 1 year ago
1
incorrect input pin state after glitch

#470 lllars opened 4 years ago
23
Configure Spindle PWM Control on ArduinoDue gShield

#469 lumascet opened 4 years ago
7
How can I compile firmware for a V9 board board153v9k?

#468 bartona opened 4 years ago
3
SPI API looks like overkill for simple startup config

#467 bobobo1618 closed 4 years ago
2