issues
search
joeylamb
/
opentx
Automatically exported from code.google.com/p/opentx
0
stars
0
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Apply curve on servo screen
#71
GoogleCodeExporter
closed
8 years ago
3
Battery Config (automatic cell setting / alarm levels)
#70
GoogleCodeExporter
closed
8 years ago
2
Enable saving your default settings to Template page
#69
GoogleCodeExporter
closed
8 years ago
1
Adjust set up values eg weight with pot
#68
GoogleCodeExporter
opened
8 years ago
2
Selecting models could be much easier
#67
GoogleCodeExporter
closed
8 years ago
9
Count down voice always says"10 seconds" for the last 10 seconds
#66
GoogleCodeExporter
closed
8 years ago
2
Add option to invert backlight
#65
GoogleCodeExporter
closed
8 years ago
2
Please disable the gray bar at the top of screen on Taranis
#64
GoogleCodeExporter
closed
8 years ago
5
Active curve point not highlighted
#63
GoogleCodeExporter
opened
8 years ago
2
[Gruvin9x] Some audio samples are mismatched to the cause
#62
GoogleCodeExporter
closed
8 years ago
10
Disable the "tick" on custom functions when changing function
#61
GoogleCodeExporter
closed
8 years ago
1
ppm delay value wrong after writing EPROM
#60
GoogleCodeExporter
closed
8 years ago
1
Remove grey bar on main screen
#59
GoogleCodeExporter
closed
8 years ago
3
Enhance usability of mixer line specification
#58
GoogleCodeExporter
closed
8 years ago
8
Reboot
#57
GoogleCodeExporter
closed
8 years ago
4
Error in simu build
#56
GoogleCodeExporter
closed
8 years ago
2
Rework the combination of slows for flight mode and mix
#55
GoogleCodeExporter
opened
8 years ago
0
DR/Expo with weight from -100% to +100%
#54
GoogleCodeExporter
closed
8 years ago
1
Increase "delay" and "slow" times
#53
GoogleCodeExporter
opened
8 years ago
1
Audio not working on sky9x 3.0 board after firmware upgrade.
#52
GoogleCodeExporter
closed
8 years ago
7
Interactive templates
#51
GoogleCodeExporter
opened
8 years ago
1
Model copy issue
#50
GoogleCodeExporter
opened
8 years ago
3
"No telemetry" alarm
#49
GoogleCodeExporter
closed
8 years ago
1
Trainer mode not turning TX all the way on.
#48
GoogleCodeExporter
opened
8 years ago
12
Swedish characters in About Box not visible
#47
GoogleCodeExporter
closed
8 years ago
3
Turnigy 9XR, "AIL D/R" and "THR. CUT" switches doesn't work
#46
GoogleCodeExporter
closed
8 years ago
11
Compilation failure, and possible simple code fix
#45
GoogleCodeExporter
closed
8 years ago
2
OpenTx does not work in version r2434
#44
GoogleCodeExporter
closed
8 years ago
16
With offset on A1/A2, mAh count up if there is no telemetry transmitted
#43
GoogleCodeExporter
closed
8 years ago
1
r2281 r2413 potscroll not working?
#42
GoogleCodeExporter
closed
8 years ago
1
If start using Slow Up and Slow Down in a mix, cease to respect the control switch
#41
GoogleCodeExporter
closed
8 years ago
21
Adding telemetry display for F.Thobois DIY hub & sensors
#40
GoogleCodeExporter
opened
8 years ago
3
Potscroll acceleration too low.
#39
GoogleCodeExporter
closed
8 years ago
7
Does Cut all Channel over 4 in the Mixer
#38
GoogleCodeExporter
closed
8 years ago
5
add "Powr+" feature to the menu to show the maximum watts used during the last flight
#37
GoogleCodeExporter
closed
8 years ago
1
Validity check on trainer input
#36
GoogleCodeExporter
opened
8 years ago
3
Short delay before activating custom functions
#35
GoogleCodeExporter
closed
8 years ago
4
maximum power reading is 655 watts with Frsky FAS-100 with the FrSky FLVS-01.
#34
GoogleCodeExporter
closed
8 years ago
1
C9X and "Bad EEPROM" going insane...
#33
GoogleCodeExporter
closed
8 years ago
6
Models displayed wrong on model menu init...
#32
GoogleCodeExporter
closed
8 years ago
1
Altitude Graphing
#31
GoogleCodeExporter
opened
8 years ago
3
modelnames does not fit to modelnumbers
#30
GoogleCodeExporter
closed
8 years ago
5
No pot scroll for Sky9x board?
#29
GoogleCodeExporter
closed
8 years ago
1
Better Count Down "Bips"
#28
GoogleCodeExporter
closed
8 years ago
18
high resolution current+consumed capacity data
#27
GoogleCodeExporter
opened
8 years ago
0
JETI navigation bug
#26
GoogleCodeExporter
closed
8 years ago
12
Curve display bug
#25
GoogleCodeExporter
closed
8 years ago
3
Trims in flight-modes should not be flight-modes specific by default
#24
GoogleCodeExporter
closed
8 years ago
19
Dual rate expo should include sliders and pots
#23
GoogleCodeExporter
closed
8 years ago
7
Customers switch sshould include switch got flight phase
#22
GoogleCodeExporter
closed
8 years ago
7
Previous
Next