Exawind hfm-fsi issues - Githubissues

Exawind / hfm-fsi

Input files and data for HFM FSI Work

0 stars 0 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Work with Derek and Andy to get the dev branch of OpenFAST going

#105 pscrozi closed 2 weeks ago
2
Move this board to ExaWind repo

#104 pscrozi opened 1 month ago
6
Resolve issue with Nalu-Wind segfaulting on GPUs.

#103 pscrozi opened 1 month ago
0
Run actuator line large wind farm simulations

#102 pscrozi opened 1 month ago
12
Run smaller case that runs faster, with IEA 15 MW, lower wind speed

#101 pscrozi opened 1 month ago
13
Run NREL 5 MW, 16 turbine case, and launch ASAP

#100 pscrozi opened 1 month ago
16
Building FSI on Summit

#99 pscrozi opened 1 month ago
10
Speed up simulations to make milestone completion feasible.

#98 pscrozi opened 1 month ago
15
Resolve issues with segfaults and other issues in ExaWind build that Lawrence and Nate were seeing

#97 pscrozi opened 1 month ago
1
Create a cleaner interface to the structural models. Generalize and create an abstraction.

#96 pscrozi opened 1 month ago
1
Figure out analogous beam representation of the flexible plate from Yulia's paper. (Part of the laminar flow validation effort.)

#95 pscrozi opened 1 month ago
7
FSI V&V Paper

#94 kevmoor opened 2 months ago
1
FY24 Q3 (NREL/Sandia): Investigation of deep-array effects in offshore wind farms:

#93 kevmoor opened 2 months ago
0
Create the API between CFD codes and turbine models. Create a cleaner interface to the structural models. Generalize and create an abstraction.

#92 pscrozi opened 2 months ago
3
Build ExaWind on Flight Sandia HPC system

#91 pscrozi opened 2 months ago
0
Pazy wing FSI validation problem

#90 pscrozi opened 2 months ago
8
Draft paper on FSI work

#89 pscrozi opened 2 months ago
4
FSI work for non-operational conditions (under SIV-VIV project)

#88 pscrozi opened 2 months ago
3
Get these FSI simulations running on Frontier.

#87 pscrozi opened 4 months ago
4
Re-run prior failure with TIOGA-Nalu-Wind fix and see if it works now.

#86 pscrozi opened 4 months ago
2
Update EAGLE FSI module build and rerun 15MW double damping with it and Ganesh's mesh

#85 kevmoor opened 4 months ago
1
Rerun Rigid Body 5MW to verify still getting the correct power without FSI

#84 kevmoor opened 4 months ago
6
Complete post-processing for IEA15MW for FSI with full power curve

#83 pscrozi opened 4 months ago
3
Complete post-processing of NREL-5MW full power curve with FSI

#82 pscrozi opened 4 months ago
4
Figure out test cases to verify the FSI capability, high priority

#81 pscrozi opened 4 months ago
4
Run IEA15MW Region III power curve with double damping

#80 pscrozi opened 4 months ago
4
Nalu, Nalu-Nalu, Nalu-AMR comparison

#79 kevmoor opened 4 months ago
25
Work on getting Sandia folks access to NREL HPC resources and viz

#78 pscrozi opened 4 months ago
3
Run more IEA15MW runs with various ideas to get stability

#77 pscrozi opened 4 months ago
6
Determine if the nodal projection was indeed monotonic along the blade span for the connected meshs, medium to low priority

#76 psakievich opened 5 months ago
0
Track down issue with negative volumes due to mesh curvature, medium priority

#75 pscrozi opened 5 months ago
3
Post-process results from IEA15MW run that Kevin did

#74 pscrozi opened 5 months ago
1
Find a test case we can use to verify the FSI capability

#73 pscrozi opened 5 months ago
3
Discuss pre-positioning of turbine blades using OpenFAST, coordinate systems, how best to mesh, particularly Phil's ideas, medium priority

#72 pscrozi opened 5 months ago
1
Create neutral build of current stack for SNL HPC's, medium priority

#71 psakievich opened 5 months ago
1
Run NREL5MW with old mesh

#70 psakievich opened 5 months ago
4
[pull] master from gantech:master

#69 pull[bot] closed 5 months ago
0
Create more general executable on SNL hardware

#68 psakievich opened 5 months ago
0
Run single regioniii case of iea15mw with consistent blending

#67 psakievich opened 5 months ago
6
[pull] master from gantech:master

#66 pull[bot] closed 5 months ago
0
Run IEA-15MW in region 3 with higher order beam (10th order)

#65 psakievich opened 5 months ago
0
Run NREL-5MW full power curve with FSI

#64 psakievich opened 5 months ago
14
Run IEA-15MW power curve with elastodyn

#63 psakievich opened 5 months ago
0
Run FSI simulation with matrix of smaller timestep, more nonlinear iterations and additional coupling between OpenFAST and Nalu-Wind

#62 psakievich opened 5 months ago
0
Run openfast with a higher order beam model and confirm the timestep required (IEA-15MW)

#61 psakievich opened 5 months ago
3
get builds of ExaWind going on Amber, or decide to go back to Eagle

#60 pscrozi opened 5 months ago
1
Discover root cause of torsional instability issues with IEA-15MW runs.

#59 pscrozi opened 5 months ago
4
Update Amber builds to use openfast's latest dev branch

#58 psakievich opened 6 months ago
1
Compare openfast cpp and fortran results of the IEA-15MW

#57 psakievich opened 6 months ago
1
Compare old run turbine parameters with the openfast cpp results, IEA-15MW

#56 psakievich opened 6 months ago
2