issues
search
Klipper3d
/
klipper
Klipper is a 3d-printer firmware
GNU General Public License v3.0
8.95k
stars
5.16k
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Added btt-kraken-v1.0 board definition
#6521
bra1nDeaD
closed
3 months ago
3
"static_value" in [output_pin enable_pin] is deprecated
#6520
1coderookie
closed
3 months ago
4
Check and warn if mcu frequency differs from configured frequency
#6519
KevinOConnor
closed
3 months ago
13
Clarify reported heater "pwm" stat after a shutdown
#6518
KevinOConnor
closed
3 months ago
0
Fix PID_CALIBRATE command when used with heater_generic
#6517
KevinOConnor
closed
3 months ago
0
config: update Kobra Plus build instructions and fan settings
#6516
dkaser
closed
3 months ago
2
Update Measuring_Resonances.md
#6515
TheParanoidEngineer
closed
2 months ago
5
Basic support for memory-mapped IO on Raspberry Pi SBCs
#6514
liampwll
opened
3 months ago
5
Fixes build on Darwin by using target toolchain gcc
#6513
apullin
opened
3 months ago
2
Update TMC_Drivers.md
#6512
KAsp3rd
opened
3 months ago
2
Add note about PrusaSlicer start gcode options
#6511
joefiorini
opened
3 months ago
2
avr: enable small code size options for atmega32u4
#6510
jaketri
closed
3 months ago
1
Update Measuring_Resonances.md
#6509
charminULTRA
closed
1 month ago
12
z_thermal_adjust: fix temperature start-up behaviour
#6508
alchemyEngine
opened
3 months ago
1
scripts: Add octopi installation on Debian Bookworm
#6507
farnasirim
closed
3 months ago
2
lpc176x: don't write to 0x2FC.
#6506
jernejp21
opened
3 months ago
3
install-ubuntu-22.04: Mark as executable
#6505
Newspaperman57
closed
2 months ago
2
remove dead code
#6504
kdomanski
closed
2 months ago
8
tmc2240: add current formatters
#6503
kdomanski
closed
1 month ago
7
tmc2240: add ADC voltage formatters
#6502
kdomanski
closed
2 months ago
3
docs: Bed_Mesh.md Correction
#6501
nuburt
opened
3 months ago
2
Adding first pass at Tenlog D3 config (32bit mainboard)
#6500
ggiraudon
opened
3 months ago
4
feat(klippy, toolhead): add S<seconds> param to G4 command
#6499
slaesh
closed
3 months ago
2
shaper_calibrate: Fixed crashes in SHAPER_CALIBRATE and TEST_RESONANCES
#6498
dmbutyugin
closed
4 months ago
1
K1 carto initial
#6497
mikebcbc
closed
4 months ago
0
K1 carto initial
#6496
mikebcbc
closed
4 months ago
0
Non critical
#6495
sbtoonz
closed
4 months ago
0
docs: updates BED_MESH_CALIBRATE description
#6494
pedrolamas
closed
3 months ago
2
Fix building for "Linux Process" in non-FHS environments
#6493
MadnessASAP
closed
2 months ago
8
[WIP] custom_component: allow to load python components natively
#6492
ayufan
opened
4 months ago
7
doc: Add required dependency to run numpy with python3 on RPI
#6491
brujoand
closed
4 months ago
5
BDsensor: adding support for new probe sensor BDsensor
#6490
markniu
opened
4 months ago
5
adxl345: Add I2C support to the ADXL345 accelerometer implementation
#6489
enduity
closed
3 months ago
4
Adding support for 100pin version of H32F460 and Tenlog D3 32bit printer
#6488
ggiraudon
closed
3 months ago
13
scripts: Added shaper tuning parameters to calibrate_shaper script
#6487
dmbutyugin
closed
4 months ago
2
idex_modes: Bugfix for kinematic position calculation.
#6486
Frans-Willem
closed
1 month ago
17
bed_mesh: support for Z in BED_MESH_OFFSET
#6485
Arksine
closed
4 months ago
5
WS2801: Support for WS2801 LEDs using SW SPI and HW SPI
#6484
akrto
opened
4 months ago
3
Remove extra bracket in Probe_Calibrate.md
#6483
nmattia
closed
4 months ago
3
klippy: Allow to open existing tty
#6482
cyberhuman
opened
4 months ago
21
Added package selection for HC32F460
#6481
ggiraudon
closed
4 months ago
2
Bed screws: fix horizontal move speed. Bed mesh: add lift speed param
#6480
gatools
opened
4 months ago
3
controller_fan: add ability to watch temperature_sensors too
#6479
slaesh
opened
4 months ago
9
Skew_Correction.md typo
#6478
streetgt
closed
4 months ago
5
support for lis3dh accelerometer
#6477
pk-love-tjy
closed
3 months ago
12
Clarify on some requirements for adaptive meshing
#6476
kyleisah
closed
2 months ago
10
Klipper flashing but not responding on the GTM332 Mini S
#6475
SonOfSardaar
closed
4 months ago
1
heater_fan: log a warning if pin is non among initial pins
#6474
kdomanski
opened
4 months ago
1
bed_mesh: behavior fixes
#6473
Arksine
closed
4 months ago
4
fix virtual SD file position count
#6472
zxy16305
closed
4 months ago
1
Previous
Next